E602 In Detail - Canon Color iR C3480 Service Manual

16.2.2 E602 in Detail

Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 / Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iR C3080i / iR
C2550
E602-XXYY
- if XX='00'
XX YY
The HDD is not recognized. The boot
01 partition (BOOTDEV) is not found at
time of start-up.
There is no system software for the main
02
CPU.
WriteAbort has been detected in
00
03
BootDevice.
The system software of the sub CPU is
06
missing.
07 ICCProfile is missing.
CHK- Partition in
XX
TYPE question
FSTDEV
01
IMG_MNG
02 1
FSTCDEV
03
APL_GEN
04
TMP_GEN
05
2
TMP_FAX
06
TMP_PSS
07
PDLDEV
08 3
BOOTDEV
09 4
APL_MEAP
10 5
APL_SEND
11 6
Not identified
FF 0
Description
1. Turn off the main switch, and check the HDD cable. Thereafter, turn on the main switch.
2. Check to see if the HDD rotates at power-up. Check to see if 5V/12V power is being supplied.
3. If the foregoing fails to correct the fault, replace the HDD and reinstall the system software. If the fault
still persists, replace the main board.
1. Start up in safe mode; then, execute full formatting using the SST, reinstall the system software (System,
Lang, RUI), and turn off and then on the main switch.
2. If the foregoing fails, suspect a fault on the HDD. Replace the HDD, and reinstall the system software.
1. Locate the sector that shows WriteAbort, and repair it.
<in the case of black-and-white E code>
1-1 Go through the following, as service mode cannot be started:
1-2 Turn off the power; then, while holding down the 1 and 9 keys, turn on the power so that the WriteAbort
sector repair routine will start automatically, causing the screen to go solid black.
1-3 Allow for some time (40 to 50 min). A progress indictor will appear. When the screen turns solid white,
the repair is over.
<in the case of spanner icon indication>
1-1 Set CHK-TYPE=0, and execute HD-CHECK (40 to 50 min); then, turn off the main switch.
2. If the foregoing fails, start up in safe mode, and execute full formatting using the SST and reinstall the
system software (System, Lang, RUI); then, turn off and then on the main switch.
3. If the fault still persists, suspect a fault on the HDD, and replace the HDD and reinstall the system
software.
1. Start up in safe mode, and execute full formatting using the SST and reinstall the system software
(System, Lang, RUI); then, turn off and then on the main switch.
2. If the foregoing fails, suspect a fault on the HDD, and replace the HDD and reinstall the system software.
1. Start up in safe mode, and execute full formatting using the SST and reinstall the system software
(System, Lang, RUI); then, turn off and then on the main switch.
2. If the foregoing fails, suspect a fault on the HDD, and replace the HDD and reinstall the system software.
XX
Description
image data storage area (e.g., Box)
image management data
image data storage area (for Chasing)
general-purpose data storage area
general-purpose data storage area (temporary file)
fax (temporary file)
PSS (temporary file)
PDL-related file storage area (font, registration form,
ICCProfile PDL function color correction information
file)
Firmware storage area (Booktable, MEAP, Key,
certificate, PDF dictionary, RUI content, voice
dictionary (ICC profile, PS test data))
MEAP
address book, filter
HDD full fault check and recovery
T-16-3
Remedial action
T-16-4
YY=03 YY=05
At time of start-up
Remedy Remedy
*1 *5
*1 *5
*1 *5
*1 *5
*1 *5
*1 *5
*1 *5
*1 *5
*3 *8
*1 *5
*2 *5
*4 *7
Chapter 16
YY
YY=10,1
YY=00,0 YY=11,2 YY=13,2
2,14,22,2
1,02,04 1 5
3,24
During normal operation
Remedy Remedy Remedy Remedy
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
*9 *10 *11 *12
0014-6885
16-15