Canon Color iR C3480 Service Manual page 667

Chapter 17
Sub item
FXS-TMP3 ITOP temperature offset (super-thick paper)
Temperature adjustment of ITOP for super-thick paper (164 to 220g paper)
This reduces the unevenness of the gloss that appears for 94 mm at the leading edges of the super-thick sheets (164 to
220g paper).
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
FXS-TMP4 ITOP temperature offset (Bk OHT)
Temperature adjustment of ITOP for Bk OHT
This reduces the unevenness of the gloss that appears for 94 mm at the leading edges of Bk OHT paper.
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
FXS-TMP5 ITOP temperature offset (4C OHT)
Temperature adjustment of ITOP for color OHT
This reduces the unevenness of the gloss that appears for 94 mm at the leading edges of color OHT paper.
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
FXS-TMP6 ITOP temperature offset (regular, thin, regular 2 1/2)
Temperature adjustment of ITOP for regular paper (64 to 105g paper) half speed
This reduces the unevenness of the gloss that appears for 94 mm at the leading edges of regular paper and half-speed
paper.
Settings
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
[Factory setting/value after clearing RAM: 0]
FXST2-N2 L/L regular 2 ITOP wait time
Pre-rotation extension for regular 2 at an outside air temperature of 18 deg C or below.
This improves the fixability of regular 2 at an outside air temperature of 18 deg C or below.
Setting range: 0 to 20
[Factory setting/value after clearing RAM: 0]
FXST2-UH L/L super-thick paper ITOP wait time
Pre-rotation extension for super-thick paper at an outside air temperature of 18 deg C or below.
This improves the fixability of super-thick paper at an outside air temperature of 18 deg C or below.
Setting range: 0 to 30
[Factory setting/value after clearing RAM: 0]
FN-ENTMP Fixing edge area cooling fan ON/OFF temperature
Fixing edge area cooling fan ON/OFF temperature
This improves the hot offset or fixability of the edge areas of standard small size paper (A4R width, LTRR width, B4
width, EXE width, K8 width, LDR width).
Settings
-4: -20 deg C
-3: -15 deg C
-2: -10 deg C
-1: -5 deg C
0: 0 deg C
+1: 5 deg C
+2: +10 deg C
+3: +15 deg C
+4: +20 deg C
[Factory setting/value after clearing RAM: 0]
FX-ASTBY Not used
FX-UP-UH SRA3 super-thick paper fixability improvement mode
Pre-rotation extension for SRA3 size (320 x 450 mm) super-thick paper
This is used to improve the fixability particularly at the image edges on SRA3 size super-thick paper.
Settings
0: 0 sec.
1: 2 sec.
[Factory setting/value after clearing RAM: 0]
17-64
COPIER>OPTION>BODY
Description level.
1
1
1
1
1
1
1
1
1