Feeder Table - Canon Color iR C3480 Service Manual

Sub item
HD-CLEAR Initializes partition specified by CHK-TYPE item.
Attention:
- The following must be kept in mind and the user must be properly informed of the fact when using CHECK-TYPE:
0: entire HDD -> no operation occurs (to initialize, use the SST)
1: image storage area -> removes image data
2: general-purpose file area (user settings data, various log data, PDL spool data, image data control information) ->
initializes files
3: PDL-related file storage area -> removes font data, requiring re-installation
4: firmware, address book, filter storage area -> no operation occurs (to initialize, use the SST)
Operation method
1) Select this item.
2) Press the OK key.
Attention:
If you perform <HD-CLEAR> after selecting 1 (image storage area) or 3 (PDL file storage area) for the <CHK-TYPE>
item, the initialization process is performed after the power is turned OFF/ON.
The initialization process takes about 5 minutes. A progress bar slowly advances to indicate the progress during this time.
Never turn the power OFF during this time.
DEBUG-1 Setting of types of logs to be saved and timing at which they are to be saved on hard disk
This specifies the types of logs to be saved and the timing at which they are to be saved on the hard disk.
Setting range
0: For saving PLOGs. They are saved when Reboot/Exception has been detected.
1: For saving PLOGs. They are saved when Reboot/Exception/Ecode has been detected.
2: For saving SUBLOGs. They are saved when Reboot/Exception/Ecode has been detected.
3: For saving SUBLOGs in the overwrite mode. They are saved when Reboot/Exception/Ecode has been detected.
[Factory setting/value after clearing RAM: 0]
Remarks
Logs of the PLOG type to be saved when "0" or "1" is set can be printed out by selecting
COPIER>FUNCTION>SYSTEM>DEBUG-2. SUBLOGs to be saved when "2" or "3" is set cannot be printed out (they
are uploaded from SST).
MEMO:
- This is not used with normal servicing. (It is used for analyzing trouble causes.)
- To use it, the instructions given by the quality support division must be followed.
DEBUG-2 Printout of logs saved on hard disk
This prints out the PLOGs to be saved when "0" or "1" has been set for COPIER>FUNCTION>SYSTEM>DEBUG-1.
Remarks
The SUBLOGs to be saved when "2" or "3" has been set for COPIER>FUNCTION>SYSTEM>DEBUG-1 are not
printed out. The number of printout sheet is about 20 in the A4 size.
MEMO:
- This is not used with normal servicing. (t is used for analyzing trouble causes.)
- To use it, the instructions given by the quality support division must be followed.
17.5.2 FEEDER

17.5.2.1 FEEDER Table

Color iR C3380G / Color iR C2880G / Color iR C3380i / Color iR C3380 / Color iR C2880i / Color iR C2880 / iR C3480 / iR C3480i / iR C3080 / iR C3080i / iR
C2550
*1; Displayed only in the case of the machine with DADF
Sub item
MTR-CHK Use it to check the motor and the like of the ADF on its own.
Operation
1) Press [MOTOR-CHK] to highlight.
2) Enter the number of the component using the keypad.
3) Press the OK key.
4) Press [MOTOR-ON[ to start checking the operation.
Settings
0: pickup motor
1: feed motor
2: delivery reversal motor
3: lock motor
[Factory default/After RAM clear: 0]
TRY-A4 Use it to execute automatic adjustment (A4 Width) for DF original paper width detection.
TRY-A5R Use it to execute automatic adjustment (A5R width) for DF original paper width detection.
TRY-LTR Use it to execute automatic adjustment (LTR width) for DF original paper width detection.
TRY-LTRR Use it to execute automatic adjustment (LTR-R width) for DF original paper width detention.
COPIER>FUNCTION>SYSTEM
Description
T-17-52
FEEDER>FUNCTION (*1)
Description
Chapter 17
level.
1
2
2
0013-9279
level.
1
1
1
1
1
17-59