Chrysler 1997 Stratus Convertible RHD Service Manual page 165

JX
SPECIFICATIONS (Continued)
BRAKE ACTUATING SYSTEM
ACTUATION:
Vacuum Operated Power Brakes . . . . . . . . Standard
Hydraulic System . . . . . . . . . . Dual-Diagonally Split
MASTER CYLINDER ASSEMBLY:
Supplier . . . . . . . . . . . . . . . . . . . . . . . . Allied Signal
Type . . . . . . . . . . . . . . . . . . . . . Center Valve Design
Body Material . . . . . . . . . . . . . . Anodized Aluminum
Reservoir Material . . . . . . . . . . . . . . . Polypropelene
MASTER CYLINDER BORE / STROKE AND
SPLIT:
ABS . . . . . . . . . . . . . . . . . . . . . 22.2 mm x 33.4 mm
Displacement Split . . . . . . . . . . . . . . . . . . . . 50 / 50
MASTER CYLINDER FLUID OUTLET PORTS:
ABS . . . . . . . . . . Primary 3/8–24 Secondary 7/16–24
Non ABS . . Primary Inboard And Outboard 7/16–24
Non ABS . Secondary Inboard And Outboard 3/8–23
Outlet Fitting Type . . . . Double Wall Inverted Flare
ABS HYDRAULIC CONTROL UNIT:
Hydraulic Tube Fitting Type . . Double Wall Inverted
Flare
BOOSTER:
Make/Type . . . . . . . . . . Allied Signal Vacuum Assist
Mounting Studs . . . . . . . . . . . . . . . . . . . . M8 x 1.25
Type . . . . . . . . . . . . . . . . . . . . . . . . 205 mm Tandem
Boost At 20 inches Of Manifold Vacuum . . . 4690 All
SCREW IN PROPORTIONING VALVE:
Material . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum
Function . . . . . . . Hydraulic Pressure Proportioning
BRAKE PEDAL
Pedal Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.32
(.874 in. x 1.32 in.)
BRAKE FASTENER TORQUE SPECIFICATIONS
DESCRIPTION
BRAKE TUBES:
Tube Nuts To Fittings And
Components . . . . . . . . . . . . . 20 N·m (180 in. lbs.)
BRAKE HOSE:
Front Caliper Banjo Bolt . . . . . 48 N·m (35 ft. lbs.)
Rear Intermediate Bracket . . 11 N·m (100 in. lbs.)
Front And Rear Brackets To
Frame Rails . . . . . . . . . . . . . . 10 N·m (95 in. lbs.)
MASTER CYLINDER:
To Vacuum Booster Mounting
Nut . . . . . . . . . . . . . . . . . . . 28 N·m (250 in. lbs.)
BRAKE BOOSTER:
To Dash Panel Mounting Nuts . 37 N·m (27 ft. lbs.)
BRAKE PEDAL
To Dash Panel Plenum Mounting
Nut . . . . . . . . . . . . . . . . . . . . . 37 N·m (27 ft. lbs.)
Shaft To Brake Pedal Bracket
Nut . . . . . . . . . . . . . . . . . . . . . 34 N·m (25 ft. lbs.)
REAR WHEEL CYLINDER:
To Support Plate Mounting Bolts . . . . . . . 13 N·m
Bleeder Screw . . . . . . . . . . . . . 10 N·m (90 in. lbs.)
BRAKE SUPPORT PLATE:
To Axle Mounting Bolts . . . . . . 75 N·m (55 ft. lbs.)
DISC BRAKE CALIPER:
Guide Pin Bolts . . . . . . . . . . . . 22 N·m (16 ft. lbs.)
Bleeder Screw . . . . . . . . . . . . . 20 N·m (15 ft. lbs.)
ABS HYDRAULIC CONTROL UNIT:
To Mounting Bracket Bolts . . 28 N·m (250 in. lbs.)
Bracket To Crossmember Mounting
Bolts . . . . . . . . . . . . . . . . . . 28 N·m (250 in. lbs.)
PARKING BRAKE:
Lever Mounting Nuts . . . . . . . 24 N·m (18 ft. lbs.)
REAR HUB AND BEARING:
To Knuckle Retaining Nut . . 250 N·m (185 ft. lbs.)
WHEEL:
Stud Lug Nut . . . . . 115–155 N·m (85–115 ft. lbs.)
BRAKES 5 - 63
TORQUE
(115 in. lbs.)