Page 1 sebring convertible 2009 owner’s manual...
Page 2 With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler LLC shall be deemed to be deleted and the features and equipment that are either standard or op- name Chrysler Canada Inc. used in substitution therefor.
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 5 INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL This Owner’s Manual has been prepared with the assis- Consult the Table of Contents to determine which section tance of service and engineering specialists to acquaint contains the information you desire. you with the operation and maintenance of your vehicle. The detailed Index at the back of this Owner’s Manual It is supplemented by a Warranty Information Booklet contains a complete listing of all subjects.
Page 7 INTRODUCTION 5...
Page 8: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 To Arm The System ....19 Ignition Key Removal .
Page 12 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Express Down Window Feature — Wind Buffeting ..... . . 36 If Equipped ......25 Trunk Lock And Release .
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Driver And Front Passenger Supplemental Lock Your Vehicle ..... 73 Restraint System (SRS) - Airbag ... 48 Exhaust Gas .
Page 14: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The authorized dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your authorized dealer.
Page 15: Ignition Key Removal
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Ignition Key Removal NOTE: Place the shift lever in PARK. Turn the ignition switch to If you try to remove the key before you place the shift the ACC position, push the key slightly inward, rotate the lever into PARK, the key may become trapped tempo- key to the LOCK position, and remove the key.
Page 16: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For vehicles equipped with the Electronic Vehicle Infor- CAUTION! mation Center (EVIC), the power window switches, radio, hands–free system (if equipped), and power An unlocked car is an invitation to thieves. Always outlets will remain active for up to 10 minutes after the remove key from the ignition and lock all doors ignition switch is turned to the LOCK position.
Page 17: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY During normal operation, after turning the ignition The Sentry Key Immobilizer System prevents unautho- switch ON, the Vehicle Security Light will turn on for rized vehicle operation by disabling the engine. The three seconds for a bulb check.
Page 18: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Replacement Keys The Sentry Key Immobilizer System is not compat- NOTE: Only keys that have been programmed to the ible with some aftermarket remote starting systems. vehicle electronics can be used to start the vehicle. Once Use of these systems may result in vehicle starting a Sentry Key has been programmed to a vehicle, it problems and loss of security protection.
Page 19: Sentry Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Sentry Key Programming Turn the ignition switch to the LOCK position and You can program new keys to the system if you have two remove the second key. valid Sentry Keys by performing the following proce- 4.
Page 20: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If a programmed key is lost, see your authorized VEHICLE SECURITY ALARM SYSTEM — IF dealer to have all remaining keys erased from the sys- EQUIPPED tems memory. This will prevent the lost key from starting The Vehicle Security Alarm system monitors the doors your vehicle.
Page 21: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 To Arm The System: NOTE: During the 16 second arming period, if a door is 1. Remove the keys from the ignition switch and get out opened or the ignition switch is turned ON, the system of the vehicle.
Page 22: Illuminated Entry System - If Equipped
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: armed when the battery is reconnected. The exterior The driver’s door key cylinder and the trunk button on lights will flash, and the horn will sound. If this occurs, the RKE transmitter cannot arm or disarm the system. disarm the system.
Page 23: Remote Keyless Entry (Rke)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 The interior lights will fade to off after about 30 seconds NOTE: or they will immediately fade to off once the ignition The line of transmission must not be blocked with switch is turned ON. metal objects when using the RKE transmitter.
Page 24: To Unlock The Doors
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock the Doors For vehicles not equipped with the EVIC, perform the Press and release the UNLOCK button on the RKE following procedure: transmitter once to unlock the driver’s door, or twice to 1.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Vehicle Security Alarm activated will cause the alarm to 1. Press and hold the UNLOCK button on a programmed sound. Press the UNLOCK button to deactivate the RKE transmitter for at least four seconds, but not longer Vehicle Security Alarm System.
Page 26: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped Sound Horn with Lock This feature activates the headlights for up to 90 seconds This feature will cause the horn to chirp when the doors when the doors are unlocked with the RKE transmitter. are locked with the RKE transmitter.
Page 27: Convertible Top Operation Button - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Release both buttons at the same time. To Unlatch the Trunk Press the TRUNK button on the RKE transmitter two 3. Test the feature while outside of the vehicle, by times to unlatch the trunk. pressing the LOCK button on the RKE transmitter with the ignition in the LOCK position, and the key removed.
Page 28: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Panic Alarm will stay on for three minutes unless Do not touch the battery terminals that are on the back you turn it off by pressing the PANIC button a second housing or the printed circuit board.
Page 29: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 2. Remove and replace the batteries. Avoid touching the NOTE: Changes or modifications not expressly ap- new batteries with your fingers. Skin oils may cause proved by the party responsible for compliance could battery deterioration.
Page 30: Remote Starting System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE STARTING SYSTEM — IF EQUIPPED NOTE: The vehicle must be equipped with an auto- This system uses the Remote Keyless Entry (RKE) trans- matic transaxle to be equipped with Remote Start. mitter to start the engine conveniently from outside the How To Use Remote Start vehicle while still maintaining security.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode To Exit Remote Start Mode and Drive the Vehicle Press and release the REMOTE START button Before the end of the 15 minute cycle, press and release on the RKE transmitter twice.
Page 32: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! (Continued) Manual Door Locks When leaving the vehicle always remove the key To lock each door, push the door lock plunger on each from the ignition lock, and lock your vehicle. door trim panel downward.
Page 33: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 Power Door Locks Automatic Door Locks A door lock switch is located on the driver and passenger When enabled, your door locks will lock automatically door trim panel. Press this switch to lock or unlock the when the vehicle’s speed exceeds 15 mph (24 km/h).
Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock Doors on Exit Programming 3. Depress the power door UNLOCK switch to unlock The Automatic Unlock Doors on Exit feature can be the doors. enabled or disabled as follows: 4. A single chime will indicate the completion of the For vehicles equipped with the Electronic Vehicle programming.
Page 35: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WINDOWS The window controls will operate when the ignition switch is turned to the ON or ACC position, and when Power Windows the accessory delay feature is active. The window controls on the driver’s door trim panel operate the door windows and the rear quarter windows.
Page 36 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Smart Glass Feature — Convertible only For vehicles not equipped with the Electronic Vehicle The door window will lower slightly if the window is Information Center (EVIC), the power window switches fully up when opening the door. The window will return will remain active for 45 seconds after the ignition switch to its full up position after closing the door.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 To reactivate the window Smart Glass Feature, perform button (setting it in the down position). To enable the the following steps after vehicle power is restored. window control, press and release the window LOCK button again (setting it in the up position).
Page 38: Wind Buffeting
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting The trunk release button on the Wind buffeting can be described as the perception of dash will be disabled if the vehicle pressure on the ears or a helicopter type sound in the is locked by pressing the power ears.
Page 39: Trunk Safety Warning
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 With the ignition ON, the word “deck” will display in the TRUNK SAFETY WARNING odometer indicating the trunk is open. The odometer WARNING! display will reappear once the trunk is closed or if the trip button is pressed.
Page 40: Trunk Internal Emergency Release
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Trunk Internal Emergency Release OCCUPANT RESTRAINTS As a security measure, a Trunk Internal Emergency Release Some of the most important safety features in your lever is built into the trunk latching mechanism. In the event vehicle are the restraint systems.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Supplemental front seat side mounted head airbags NOTE: The front airbags have a dual-stage inflator design. This allows the airbag to have different rates of Front seat belt retractors that incorporate pretension- inflation that are based on collision severity.
Page 42: Lap/Shoulder Belts
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even normal conditions. However, in a collision, the belt will on short trips. Someone on the road may be a poor driver lock and reduce the risk of your striking the inside of the and cause a collision that includes you.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 2. The seat belt latch plate is on the outboard side of the WARNING! (Continued) front seat, next to your arm. Grasp the latch plate and Wearing your belt in the wrong place could make pull out the belt.
Page 44 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” A belt that is buckled into the wrong buckle will not protect you properly.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! (Continued) A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt.
Page 46: Lap/Shoulder Belt Untwisting Procedure
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! A lap belt worn too high can increase the risk of A frayed or torn belt could rip apart in a collision and internal injury in a collision. The belt forces won’t be leave you with no protection.
Page 47: Seat Belt Pretensioners
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 2. At about 6 to 12 in (15 to 30 cm) above the latch plate, in a collision. Pretensioners work for all size occupants, grasp and twist the belt webbing 180° to create a fold that including those in child restraints.
Page 48: Enhanced Seat Belt Reminder System (Beltalert )
NOTE: Watch for the Seat Belt Warning Light to turn on dealer or by performing the following steps: while unbuckling and turn off while re-buckling the seat belt. It may be necessary to retract the seat belt partially NOTE: Chrysler LLC does not recommend deactivating after unbuckling it. BeltAlert .
Page 49: Automatic Locking Mode
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 4. Turn the ignition switch to the LOCK position. A How To Engage the Automatic Locking Mode single chime will sound to signify that you have success- 1. Buckle the combination lap/shoulder belt. fully completed the programming.
Page 50: Seat Belts And Pregnant Women
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belts and Pregnant Women WARNING! We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is Using a seat belt extender when not needed can the best way to keep the baby safe.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 The front airbags have a dual-stage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. WARNING! Do not put anything on or around the front airbag covers or attempt to open them manually.
Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE collisions, both the front and seat airbags may be trig- WARNING! (Continued) gered. However, even in collisions where the airbags Do not attach cup holders or any other objects on work, you need the seat belts to keep you in the right or around the door.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 restraints or belt-positioning booster seats. Older chil- 4. If your vehicle has seat airbags, do not lean against dren who do not use child restraints or belt-positioning the door, airbags will inflate forcefully into the space booster seats should ride properly buckled up in the rear between you and the door.
Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat Side (Thorax and Head) Airbags WARNING! (Continued) Front Impact Sensors Being too close to the steering wheel or instrument panel during front airbag deployment could cause Side Impact Sensors (if equipped) serious injury.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The first stage inflator is triggered immediately during an Front Passenger Airbag Special Features impact that requires airbag deployment. The timing of A new active venting front-passenger airbag is designed the second stage determines whether the output force is to reduce the risk of occupants who may be out of low, medium, or high.
Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of Airbag Warning Light either momentarily or continu- the system whenever the ignition switch is in the START ously. A single chime will sound if the light comes on or ON position.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Impact Sensors Two sensors, located on the front body structure, trigger airbag deployment in direct frontal impacts and aid the ORC in determining appropriate response to frontal impact events. Additional sensors in the ORC determine the level of airbag deployment and provide verification.
Page 58 Each bag deploys independently, that is a left side impact those which are approved by Chrysler LLC/Mopar. deploys the left bag only and a right-side impact deploys only the right bag.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If A Deployment Occurs However, if you haven’t healed significantly within a The airbag systems are designed to deploy when the few days, or if you have any blistering, see your doctor Occupant Restraint Controller (ORC) detects a moderate- immediately.
Page 60 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Turns on the interior lights, which remain on as long as WARNING! the battery has power or until the ignition key is removed Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, Unlocks the doors automatically seat belt pretensioners, and the front passenger seat Maintaining Your Airbag System...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 NOTE: Perchlorate Material — special handling may WARNING! (Continued) apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. It is dangerous to try to repair any part of the Airbag Warning Light airbag system yourself. Be sure to tell anyone who You will want to have the airbags ready to works on your vehicle that it has an airbag system.
Page 62: Event Data Recorder (Edr)
Chrysler LLC and others to learn more about the eters (see the following list) in an event data recorder possible causes of crashes and associated injuries in order prior to the moment of airbag deployment, or near to assess and improve vehicle performance.
Page 63 (usually preserved. the vehicle owner or lessee) before accessing the elec- 2. Used in defense of litigation involving a Chrysler LLC tronic data stored, unless ordered to download data by a product. court with legal jurisdiction (i.e., pursuant to a warrant).
Page 64: Child Restraints
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag deployment level (if applicable) small children ride in proper restraint systems. This is the law, and you can be prosecuted for ignoring it. Impact acceleration and angle Children 12 years and younger should ride properly Seat belt status buckled up in a rear seat, if available.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 There are different sizes and types of restraints for infant carriers do, so they can be used rearward-facing children from newborn size to the child almost large by children who weigh more than 20 lbs (9 kg) but are enough for an adult safety belt.
Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE who weigh 20 to 40 lbs (9 to 18 kg) and who are older Children Too Large for Booster Seats than one year. These child seats are also held in the Children who are large enough to wear the shoulder belt vehicle by the lap/shoulder belt or the LATCH child comfortably, and whose legs are long enough to bend restraint anchorage system.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 bend over the front of the seat when their back is WARNING! against the seatback, should use the lap/shoulder belt in a rear seat. Improper installation can lead to failure of an infant or child restraint.
Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All passenger seating positions contain automatic for the installation of the child restraint without using the locking retractors. However, any seat belt system will vehicle’s seat belts. The two rear seating positions have loosen with time, so check the belt occasionally and lower anchorages that are capable of accommodating pull it tight if necessary.
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 to the top tether anchorage have been available for some Because the lower anchorages are to be introduced to time. In fact, many child restraint manufacturers will passenger carrying vehicles over a period of years, child provide add-on tether strap kits for some of their older restraint systems having attachments for those anchor- products.
Page 70 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remind all children in the vehicle that the seat belts are In addition, there are tether strap anchorages not toys and should not be played with, and never leave behind each rear seating position. Access ports your child unattended in the vehicle.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 seat cover material. Then rotate the tether anchorage stow the seat belt out of the reach of an inquisitive child. cover directly behind the seat where you are placing the Remind all children in the vehicle that the seat belts are child restraint and attach the tether strap to the anchor- not toys and should not be played with, and never leave age, being careful to route the tether strap to provide the...
Page 72 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belt must be in the Automatic Locking mode in buckle and twist the short buckle-end belt several times order to enable a child restraint to be tightly installed. to shorten it. Insert the latch plate into the buckle with the Refer to “Automatic Locking Mode”...
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 4. Open the access cover (C) on the carpet covering the back of the seat and attach the tether strap hook (D) to the anchor. Child Tether Access Port Cover 3. Push the tether strap and hook (B) through the access port and down into the trunk.
Page 74: Engine Break-In Recommendations
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 75: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 shown under “Engine Oil”, under “Maintenance Proce- WARNING! dures” in section 7 of this manual. NON-DETERGENT OR STRAIGHT MINERAL OILS MUST NEVER BE It is extremely dangerous to ride in a cargo area, USED.
Page 76: Exhaust Gas
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Exhaust Gas If you are required to drive with the trunk open, make sure that all windows are closed, and the blower switch WARNING! on the climate control is set at high speed. DO NOT use the recirculation mode.
Page 77: Safety Checks You Should Make Inside The
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 Safety Checks You Should Make Inside the authorized dealer. If the light stays on, flickers, or comes Vehicle on while driving, have the system checked by an autho- rized dealer. Seat Belts Inspect the seat belt system periodically, checking for Defroster cuts, frays, and loose parts.
Page 78 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Fluid Leaks Have someone observe the operation of exterior lights Check area under vehicle after overnight parking for fuel, while you work the controls. Check turn signal and high engine coolant, oil, or other fluid leaks. Also, if gasoline beam indicator lights on the instrument panel.
Page 79: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Convertible Top Operation ....81 Power Convertible Top Operation And Warning Messages ....94 Power Convertible Top Usage Precautions .
Page 80 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Hands-Free Communication (UConnect ) — Seats ......135 If Equipped .
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Headlights With Wipers (Available With Headlights With Wipers (Available With Auto Headlights Only) ....144 Auto Headlights Only) ....153 Headlight Time Delay —...
Page 82 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming ..162 Heated Or Cooled Cupholder — If Equipped ......168 Security .
Page 83: Convertible Top Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 CONVERTIBLE TOP OPERATION The top does take up some space in the trunk when retracted. However, the trunk will still hold a significant WARNING! amount of cargo. When operating the power convertible top, the trunk lid The convertible top does not provide the structural will pivot at the rear of the vehicle, swing open by the protection that a reinforced metal roof does and the...
Page 84: Power Convertible Top Usage Precautions
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To complete either operation, the trunk lid returns to its micro-switches verify that operations are complete normal position and then latches. before allowing the next stage of lowering or raising operation. Spring-loaded flipper doors, which provide clearance for the linkage, close off notches in the quarter trim panels Opening and closing the top consecutively without the when the top is up.
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 CAUTION! (Continued) CAUTION! (Continued) Always place items carefully into the trunk. Make sure the ambient temperature is above 0°F (-18°C). Do not push items too far into the trunk, particu- larly when the top is retracted into its stowage area Never attempt to lower a frozen convertible top.
Page 86 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) CAUTION! (Continued) Failure to follow these cautions can cause damage to Always use a normal ice scraper to remove snow or the convertible top components, trunk contents, and ice from the rear window. Use of a sharp object or the vehicle interior.
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 WARNING! WARNING! (Continued) When using the power top switch on the instru- Before operating the power top, make sure that no ment panel, if potential danger exists while raising moving parts of the convertible top can injure a the top, release the switch immediately to inter- person or animal.
Page 88: Cargo Shield
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Shield The cargo shield is located in the trunk. Before lowering the convertible top, you must unfold the cargo shield and seat the tabs at each end of the cargo shield in the V slots in the trunk liner.
Page 89: Power Convertible Top Controls
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 panel forward onto the horizontal panel, then grasp both Power Convertible Top Controls panels and lift them to the forward, upright position in The power top switch is located on the instrument panel the trunk.
Page 90: Lowering The Power Convertible Top
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is also a power top button on the Remote Keyless Lowering the Power Convertible Top Entry (RKE) transmitter for remotely lowering the power Using the Power Top Switch convertible top. NOTE: The power top switch will operate when the ignition switch is turned to the ON or ACC position and when in the power accessory delay.
Page 91: Raising The Power Convertible Top
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Using the Remote Keyless Entry (RKE) Transmitter Press and hold the switch in the Top Up position until the operation of raising the top NOTE: Steps 1 – 3 must be performed within five and latching it is complete, which is indicated seconds.
Page 92: Manual Bypass Mode
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Read all of the Notes, Cautions, and Warning found NOTE: This process may take a more significant under “Power Convertible Top Usage Precautions” to amount of time to fully close the power top. It’s not verify all operating conditions are met.
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 3. Lay the small frame (1) flat on top of the large frame 4. Pivot the small frame (1) away from the large frame (2) (2) and snap the two frames together by engaging the until the pivot lock (3) engages to lock the two frames in frame lock (3).
Page 94 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Unfold both stems at the rear of the large frame. 6. Align and insert the stems into the slot in each trim panel.
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 7. Align the pins at the front of the large frame with the Removing and Storing the Wind Stop hole in each trim panel. Slide the pins outward until fully Reverse the installation procedure to remove, fold, and extended into each hole.
Page 96: Power Convertible Top Operation And Warning Messages
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE (EVIC) – if equipped, or in the Odometer for vehicles not Power Convertible Top Operation and Warning equipped with the EVIC. Refer to the following chart for Messages When the appropriate conditions exist, the PTCM dis- message related information: plays various power convertible top operation and warn- ing messages in the Electronic Vehicle Information Center...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time SECURE 9 Seconds Display...
Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time SPEED 9 Seconds SPEED...
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 EVIC EVIC Odometer Odometer Odometer Odometer Chime Condition Operator Message Message Message Message Message Message Action Display (< 5 mph Display (> 5 mph Display Required Time [8 km/h]) Time [8 km/h]) Time CONVERT- 6 Seconds TOP FAIL...
Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The PTCM will lockout the power convertible top system if the vehicle charging system is malfunctioning, or the battery is run down, or the hydraulic pump is overheating. In addition, the system prohibits lowering the top when ambient temperature is at 0°F (-18°C) or lower and raising the top when ambient temperature is below -40°F (-40°C).
Page 101: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light will illuminate to indicate when the dimming feature is activated.
Page 102: Outside Mirrors
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! WARNING! To avoid damage to the mirror during cleaning, never Vehicles and other objects seen in the passenger side spray any cleaning solution directly onto the mirror. convex mirror will look smaller and farther away Apply the solution onto a clean cloth and wipe the than they really are.
Page 103: Heated Power Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Power Mirror Adjust Switch Mirror Directions After selecting a mirror, move the knob in the same Heated Power Mirrors — If Equipped direction you want the mirror to move. When finished, These mirrors are heated to melt frost or ice. This feature return the knob to the center “O”...
Page 104: Vanity Mirror - If Equipped
UConnect system operating instructions for these ra- following websites: dios. Radio sales code can be located on the lower right corner of the Radio faceplate. www.chrysler.com/uconnect UConnect is a voice-activated, hands-free, in-vehicle www.dodge.com/uconnect communications system. UConnect allows you to dial a www.jeep.com/uconnect...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 UConnect allows you to transfer calls between the Phone Button system and your cellular phone as you enter or exit your The rearview mirror contains the microphone vehicle and enables you to mute the system’s microphone for the system (depending on the type of for private conversation.
Page 106: Operation
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect system is fully integrated with the vehi- For certain operations, compound commands can be cle’s audio system. The volume of the UConnect system used. For example, instead of saying Setup and then can be adjusted either from the radio volume control Phone Pairing, the following compound command knob or from the steering wheel radio control (right...
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Help Command To complete the pairing process, you will need to refer- If you need assistance at any prompt, or if you want to ence your cellular phone Owner’s Manual. The know your options at any prompt, say Help following UConnect website may also provide detailed instruc- the beep.
Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For identification purposes, you will be prompted to Dial by Saying a Number give the UConnect system a name for your cellular Press the PHONE button to begin. phone. Each cellular phone that is paired should be given a unique phone name.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 The system will prompt you to say the name of the After the Ready prompt and the following beep, say person you want to call. Phonebook New Entry. After the Ready prompt and the following beep, say When prompted, say the name of the new entry.
Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect system will allow you to enter up to 32 Automatic download and update, if supported, begins names in the phonebook with each name having up to as soon as the Bluetooth wireless phone connection is four associated phone numbers and designations.
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 This downloaded phonebook cannot be edited or Some phones cannot send phonebook entries if they deleted on the UConnect . These can only be edited on are already connected to any system via Bluetooth , the mobile phone.
Page 112 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the PHONE button to begin. mobile and a home number, but you can add ”John Doe’s” work number later using the Phonebook Edit After the Ready prompt and the following beep, say feature.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 from the list, press the VOICE RECOGNITION button The UConnect system will ask you to verify that you while the UConnect system is playing the desired wish to delete all the entries from the phonebook. entry and say Delete.
Page 114: Phone Call Features
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To call one of the names in the list, press the VOICE Answer or Reject an Incoming Call - No Call RECOGNITION button during the playing of the Currently in Progress desired name, and say Call. When you receive a call on your cellular phone, the UConnect system will interrupt the vehicle audio sys- NOTE: The user can also exercise Edit or Delete...
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 NOTE: The UConnect system compatible phones in Place/Retrieve a Call From Hold the market today do not support rejecting an incoming To put a call on hold, press the PHONE button until you call when another call is in progress.
Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Three-Way Calling After the Ready prompt and the following beep, say To initiate three-way calling, press the VOICE RECOG- Redial. NITION button while a call is in progress, and make a The UConnect system will call the last number that second phone call, as described under Making a Second was dialed from your cellular phone.
Page 117: Uconnect System Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 After the ignition key is switched to OFF, a call can After selecting one of the languages, all prompts and continue on the UConnect system for a certain dura- voice commands will be in that language. tion, after which the call is automatically transferred NOTE: After every UConnect language change opera- from the UConnect system to the mobile phone.
Page 118 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After the Ready prompt and the following beep, say WARNING! Emergency and the UConnect system will instruct the paired cellular phone to call the emergency num- Your phone must be turned on and paired to the ber.
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 NOTE: Working with Automated Systems The towing assistance number dialed is based on the This method is used in instances where one generally has country where the vehicle is purchased (1-800-528- to press numbers on the cellular phone keypad while 2069 for the U.S., 1-877-213-4525 for Canada, 55-14- navigating through an automated telephone system.
Page 120 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE or sequence of numbers, followed by Send, is also to be Some paging and voice mail systems have system time used for navigating through an automated customer out settings that are too short and may not allow the service center menu structure, and to leave a number on use of this feature.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 After the Ready prompt and the following beep, say phone, the audio will be played through your vehicle’s Setup Confirmations. The UConnect system will audio system. The UConnect system will work the same play the current confirmation prompt status and you as if you dial the number using voice recognition.
Page 122: Advanced Phone Connectivity
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE In order to un-mute the UConnect system: If you would like to connect or disconnect the Bluetooth connection between a UConnect paired cellular phone Press the VOICE RECOGNITION button. and the UConnect system, follow the instructions de- Following the beep, say Mute off.
Page 123: Things You Should Know About Your Uconnect System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Select Another Cellular Phone Delete UConnect Paired Cellular Phones This feature allows you to select and start using another Press the PHONE button to begin. phone paired with the UConnect system. After the Ready prompt and the following beep, say Press the PHONE button to begin.
Page 124 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training This procedure may be repeated with a new user. The For users experiencing difficulty with the system recog- system will adapt to the last trained voice only. nizing their voice commands or numbers, the UConnect To restore the Voice Recognition system to factory default system Voice Training feature may be used.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 low-to-medium blower setting, It is not recommended to store similar sounding names in the UConnect phonebook. low-to-medium vehicle speed, Phonebook (Downloaded and UConnect Local) name low road noise, recognition rate is optimized when the entries are not smooth road surface, similar.
Page 126 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE low-to-medium vehicle speed, In a convertible vehicle, system performance may be compromised with the convertible top down. low road noise, Bluetooth Communication Link smooth road surface, Cellular phones have been found to lose connection to fully closed windows, the UConnect system.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125...
Page 128 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127...
Page 130 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 132: General Information
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE RECOGNITION SYSTEM (VR) — IF This device complies with Part 15 of the FCC rules and EQUIPPED RSS 210 of Industry Canada. Operation is subject to the Voice Recognition System (VR) Operation following conditions: This Voice Recognition system allows you to Changes or modifications not expressly approved by...
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 When you press the VR hard-key, you will hear a beep. These commands are universal and can be used from any The beep is your signal to give a command. menu. All other commands can be used depending upon the active application.
Page 134: Commands
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands In this mode, you can say the following commands: The Voice Recognition system understands two types of “Radio” (to switch to the radio mode) commands. Universal commands are available at all times. Local commands are available if the supported “Disc”...
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Radio FM “Previous Channel” (to select the previous channel) To switch to the FM band say “FM” or “Radio FM”. In “List Channel” (to hear a list of available channels) this mode, you may say the following commands: “Select Name”...
Page 136 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo − “Previous” (to play the previous memo) To switch to the voice recorder mode say “Memo”. In this − “Delete” (to delete a memo) mode, you may say the following commands: “Delete All” (to delete all memos) “New Memo”...
Page 137: Voice Training
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Voice Training SEATS For users experiencing difficulty with the system recog- Power Seats nizing their voice commands or numbers, the UConnect The power seat switch is on the outboard side of the seat system Voice Training feature may be used.
Page 138: Heated Seats - If Equipped
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped CAUTION! Heated seats provide comfort and warmth on cold days and can help soothe sore muscles and backs. The driver Do not place any article under any seat as it may and front passenger seats are heated.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 140: Recliner Adjustment
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment The recliner control is on the outboard side of the seat. To recline the seat, lean forward slightly and lift the lever. Then lean back to the position desired and release the lever.
Page 141: Lumbar Support - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 142: Easy Entry System
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry System On the passenger seat, pull the lever upward to move the The Easy Entry lever is located on upper seat belt anchor seat and seatback forward. cover. When returning the seat to its normal position, the memory feature restores the seat position and seatback recline position to their current settings.
Page 143: Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraint so that the upper edge is as high as practical. To raise it, pull upward on the head restraint.
Page 144: To Open And Close The Hood
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Move to the outside of the vehicle and lift the second- Two latches must be released to open the hood. ary latch underneath the center front edge of the hood. Then, raise the hood.
Page 145: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Use the hood prop rod to secure the hood in the open slam the hood to close it. Use a firm downward push at position. Place the upper end of the prop rod in the hole the center of the hood to ensure that both latches engage.
Page 146: Headlights And Parking Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Automatic Headlights — If Equipped Turn the end of the multifunction lever to the first detent This system automatically turns the headlights on or off for parking light operation. Turn the end of the lever to according to ambient light levels.
Page 147: Headlight Time Delay - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 In addition, the headlights will turn off when the wipers If you turn the headlights, parking lights, or ignition are turned off if they were turned on by this feature. switch ON again, the system will cancel the delay. The Headlights with Wipers feature can be turned on or If you turn the headlights off before the ignition, they will off through the Electronic Vehicle Information Center...
Page 148: Lights-On Reminder
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The Daytime Running Lights will turn off automatically when the turn signal is in operation and turn on again when the turn signal is not operating. Lights-On Reminder If the headlights or parking lights are on after the ignition is turned to the LOCK position, a chime will sound to alert the driver when the driver’s door is opened.
Page 149: Turn Signals
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Turn Signals Check for a defective outside light bulb if either light Move the multifunction lever upward or downward and remains on and does not flash or has a very fast flash rate. the corresponding turn signal indicator on the instru- If an indicator fails to light when the lever is moved, it ment panel will flash to show proper operation of the...
Page 150: High Beam/Low Beam Select Switch
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Beam/Low Beam Select Switch Flash-To-Pass Push the multifunction lever away from you to switch You can signal another vehicle with your headlights by the headlights to high beam. Pull the multifunction lever lightly pulling the multifunction lever toward you.
Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 A courtesy light is also found in the rear of the center console. You can turn this light on and off from the dimmer control in the multifunction lever. This light is also controlled automatically by the Illuminated Entry System.
Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dimmer Control Instrument Panel Dimming The dimmer control is part of the multifunction lever. It With the parking lights or headlights on, rotate the controls the operation of the interior lights and the dimmer control upward or downward to change the brightness of the instrument panel lights.
Page 153: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 WINDSHIELD WIPERS AND WASHERS Rotate the end of the lever to the first detent past the The windshield wiper/washer control lever is intermittent settings for Low-speed wiper operation, or located on the right side of the steering column. to the second detent past the intermittent settings for high-speed wiper operation.
Page 154: Intermittent Wiper System
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE For vehicles equipped with the Speed Sensitive Intermit- CAUTION! (Continued) tent Wiper System, the wiper delay times depend on Always remove any buildup of snow that prevents vehicle speed. If the vehicle is moving less than 10 mph the windshield wiper blades from returning to the (16 km/h), delay times will double.
Page 155: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Mist Feature Headlights with Wipers (Available with Auto Push downward on the windshield wiper/washer con- Headlights Only) trol lever to activate a single wipe cycle to clear the When this feature is active, the headlights will turn on windshield of road mist or spray from a passing vehicle.
Page 156: Tilt/Telescoping Steering Column
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you activate the washer while the wiper control is in the delay range, the wipers will operate in low speed for two wipe cycles after releasing the lever and then resume the intermittent interval previously selected. If you activate the washer while the wiper control is in the off position, the wipers will operate for two wipe cycles and then turn off.
Page 157: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 The Electronic Speed Control lever is located on the right WARNING! side of the steering wheel. Do not adjust the steering wheel while driving. The tilt/telescoping adjustment must be locked while driving. Adjusting the steering wheel while driving or driving without the tilt/telescoping adjustment locked could cause the driver to lose control of the vehicle.
Page 158: To Activate
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate To Set At A Desired Speed Push and release the ON/OFF button located When the vehicle reaches the speed desired, press down on the end of the Electronic Speed Control on the lever and release SET DECEL. Release the accel- lever.
Page 159: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 To Resume Speed To decrease speed while the Electronic Speed Control is If you deactivated the Electronic Speed Control without set, push down and hold the lever SET DECEL. Release erasing the set speed from memory and your vehicle the lever when the desired speed is reached, and the new speed is above 20 mph (32 km/h) you can resume the set speed will be established.
Page 160: To Accelerate For Passing
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing The HomeLink buttons that are located in the headliner Depress the accelerator as you would normally. When the or sun visor designate the three different HomeLink pedal is released, the vehicle will return to the set speed. channels.
Page 161: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Programming Homelink WARNING! Before You Begin Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the universal transceiver. erase all channels before you begin training. Do not train the transceiver if people or pets are in To do this, press and hold the two outside buttons for up the path of the door or gate.
Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Begin Programming NOTE: Some gate operators and garage door openers may 1. Turn the ignition switch to the ON/RUN position. require you to replace Step 3 with procedures noted in 2. Hold the battery side of the handheld transmitter the “Gate Operator/Canadian Programming”...
Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 If the indicator light blinks rapidly for two seconds and then turns to a constant light, proceed to Step 5 “Pro- gramming A Rolling Code System.” 5. Programming A Rolling Code System At the garage door opener motor (in the garage), locate the “Learn”...
Page 164: Gate Operator/Canadian Programming
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: There are 30 seconds in which to initiate the next trained device (i.e., garage door opener, gate operator, step after the “Learn” button has been pressed. security system, entry door lock, home/office lighting, etc.
Page 165: Security
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 to pick up the signal during programming. Similar to this Then proceed with Step 4 under “Programming Canadian law, some U.S. gate operators are designed to HomeLink ,” earlier in this section. time-out in the same manner. Security It may be helpful to unplug the device during the cycling It is advised to erase all channels before you sell or turn...
Page 166: General Information
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the “Learn” button on the Garage Door Opener NOTE: to complete the training for a Rolling Code. The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not Did you unplug the device for training, and remember expressly approved by the party responsible for com- to plug it back in?
Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 NOTE: If desired, the instrument panel power outlet The center console power outlet is powered directly from can be converted by your authorized dealer to provide the battery (power available at all times). Items plugged power with the ignition switch while in the LOCK into this outlet may discharge the battery and/or prevent position.
Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! To avoid serious injury or death: Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in Do not use a three-prong adapter. use (i.e., cellular phones, etc.). Eventually, if Do not insert any objects into the receptacles.
Page 169: Cigar Lighter And Ash Receiver - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 CIGAR LIGHTER AND ASH RECEIVER — IF CAUTION! EQUIPPED An optional ash receiver is available from your autho- For vehicles equipped with the heated and cooled rized dealer and will fit in the center console front cupholder, locate the cup holder ash receiver in the cupholder.
Page 170: Heated Or Cooled Cupholder - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated or Cooled Cupholder — If Equipped With this feature, the rear cavity of the cupholder can keep cool beverages cool, and hot beverages hot. The rear cupholder heats to 140°F (60°C) or cools to 35°F (1.6°C). The switch is located on the front of the center console and has three positions: Heat, Off, Cool.
Page 171: Rear Seat Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 Rear Seat Cupholders Cupholders for the rear seat occupants are located in the armrests. Each cupholder is capable of holding up to a 20 oz. (.5 L) bottle or can. Rear Seat Cup Holder...
Page 172: Console Features
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Storage The center console contains a cubby bin with flip-down cover located below the climate controls. This compart- ment also contains a 12-Volt electrical outlet. WARNING! Do not place ashes inside the cubby bin located on the center console.
Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Two separate storage compartments are also located underneath the armrest. 1 — Release button for top compartment 2 — Release button for bottom compartment 3 — Top Compartment 4 — Bottom Compartment. You can access this compartment directly, without first exposing the upper compartment, by oper- ating the Release Button for the bottom compartment with the armrest down.
Page 174: Sliding Armrest - If Equipped
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The top compartment holds small items, such as a pen Sliding Armrest — If Equipped and note pad, while the larger bottom compartment will On some models, the center console armrest slides for- hold CDs and alike.
Page 175: Rear Window Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 REAR WINDOW FEATURES CAUTION! Rear Window Defroster — If Equipped To avoid damaging the electrical conductors of the The electric Rear Window Defroster switch is rear window defroster, do not use scrapers, sharp located on the climate control.
Page 177: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....178 Compass Display ....198 Instrument Cluster –...
Page 178 176 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files ..214 Operating Instructions — Radio Mode ..222 List Button (Disc Mode For MP3/WMA Operation Instructions — CD Mode For CD Play) .
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 177 Satellite Radio (RSC) — If Equipped Right-Hand Switch Functions ... . 248 (RER/REQ/REN Radios Only)... . . 243 Left-Hand Switch Functions For Radio System Activation .
Page 180: Instrument Panel Features
178 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Outlet 6 — Radio 11 — Hazard Switch 2 — Side Window Demister Outlet 7 — Passenger Airbag 12 — Storage Compartment 3 — Instrument Cluster 8 — Glove Box 13 —...
Page 181: Instrument Cluster - Base
UNDERSTANDING YOUR INSTRUMENT PANEL 179 INSTRUMENT CLUSTER – BASE...
Page 182: Instrument Cluster - Premium
180 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – PREMIUM...
Page 183: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 181 INSTRUMENT CLUSTER DESCRIPTIONS If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. 1. Fuel Gauge Idle the vehicle with the air conditioner turned off until When the ignition switch is in the ON position, the the pointer drops back into the normal range.
Page 184 182 UNDERSTANDING YOUR INSTRUMENT PANEL 5. Low Fuel Light 7. Airbag Warning Light When the fuel level drops to approximately 2.0 gal- The light comes on and remains on for six to lons (7.6 Liters), the fuel symbol will light and a eight seconds as a bulb check when the ignition single chime will sound.
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 183 9. Seat Belt Reminder Light The light does not show the quantity of oil in the engine. When the ignition switch is first turned ON, this This can be determined using the procedure shown in light will come on for about six seconds.
Page 186 184 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: You must apply the brakes before shifting from Vehicle Warning Messages PARK. When the appropriate conditions exist, “door,” “deck,” “LoW TirE,” “CHAngE OIL,” “GASCAP” or “HOTOIL” 14. Odometer/Trip Odometer will display in the odometer. The odometer shows the total distance the vehicle has been driven.
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 185 GASCAP means the engine oil change interval may fluctuate If the vehicle diagnostic system detects a leak or change dependent upon your personal driving style. in the evaporative system, or the fuel filler cap is loose, Unless reset, this message will continue to display each improperly installed, or damaged, the words “GASCAP”...
Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL 4. For vehicles equipped with the Electronic Vehicle To reset the trip odometer, first set the display to Trip Information Center (EVIC), refer to “Electronic Vehicle Mode. Then push and hold the button (approximately Information Center (EVIC)” in this section of the 2 seconds) until the display resets to 0 miles.
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 187 17. Electronic Throttle Control (ETC) Indicator Light 18. Electronic Stability Program (ESP) Indicator Light This light informs you of a problem with the / Traction Control System (TCS) Indicator Light — If Electronic Throttle Control (ETC) system. If a Equipped problem is detected, the light will come on If this indicator light flashes during accelera-...
Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- WARNING! ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is Driving a vehicle with the brake light on is danger- indicated by the Brake Warning Light which will turn on ous.
Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL 189 The light also will turn on when the parking brake is Warning Lamp” should turn off with the engine running. applied with the ignition switch in the ON position. If the “ESP/BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected NOTE: This light shows only that the parking brake is in either the ESP or the BAS system.
Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL If the ABS light is on, the brake system should be serviced As an added safety feature, your vehicle has been as soon as possible to restore the benefit of Anti-Lock equipped with a Tire Pressure Monitoring System Brakes.
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 191 Your vehicle has also been equipped with a TPMS CAUTION! malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is The TPMS has been optimized for the original combined with the low tire pressure telltale. When the equipment tires and wheels.
Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Malfunction Indicator Light (MIL) If the MIL flashes when the engine is running, serious The Malfunction Indicator Light (MIL) is part of conditions may exist that could lead to immediate loss of an onboard diagnostic system called OBD that power or severe catalytic converter damage.
Page 195: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 193 ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) – IF EQUIPPED System Status The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the Vehicle information warning message displays instrument cluster.
Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by Press and release the COMPASS button to pressing the following buttons on the Instrument Panel display the compass heading and the outside Switch Bank: temperature. COM- Press and release the MENU button to advance PASS the display to Trip Functions or Personal Set-...
Page 197: Electronic Vehicle Information Center (Evic) Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Electronic Vehicle Information Center (EVIC) Personal Settings Not Available – Vehicle in Motion Displays Left/Right Door Ajar (one or more, with a single When the appropriate conditions exist, the Electronic chime if speed is above 1 mph) Vehicle Information Center (EVIC) displays the following messages.
Page 198: Oil Change Required
196 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required 2. Fully depress the accelerator pedal slowly three times Your vehicle is equipped with an engine oil change within 10 seconds. indicator system. The “Oil Change Required” message 3. Turn the ignition switch to the LOCK position. will flash in the EVIC display for approximately five seconds after a single chime has sounded to indicate the NOTE: If the indicator message illuminates when you...
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 197 The Trip Functions mode displays the following informa- When the DTE value is less than 30 miles (48 km) tion: estimated driving distance, the DTE display will change to a text display of LOW FUEL. This display will con- Average Fuel Economy tinue until the vehicle runs out of fuel.
Page 200: Compass Display
198 UNDERSTANDING YOUR INSTRUMENT PANEL To reset all resettable functions, press and release the or metallic objects) until the CAL indicator in the EVIC RESET button a second time within three seconds of turns off. The compass will now function normally. resetting the currently displayed function (Reset ALL will Manual Compass Calibration display during this three-second window).
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 5. Drive the vehicle slowly, completing one or more circles (in an area free from large metal or metallic objects) until the CAL indicator turns off. The compass will now function normally. Compass Variance Compass Variance is the difference between magnetic North and Geographic North.
Page 202: Personal Settings (Customer-Programmable Features)
200 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Press and release the STEP button until “Compass Press and release the MENU button until “Personal Variance” and the current Variance Value displays in the Settings” displays in the EVIC. EVIC. Press and release the STEP button to display the follow- 4.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 201 Remote Key Unlock Flash Lights with LOCK When Driver Door 1st Press is selected, only the driver’s When ON is selected, the front and rear turn signals will door will unlock on the first press of the Remote Keyless flash when the doors are locked or unlocked with the Entry transmitter UNLOCK button.
Page 204: Setting The Analog Clock
202 UNDERSTANDING YOUR INSTRUMENT PANEL off if they were turned on by this feature. To make your unlocked with the RKE transmitter. To make your selec- selection, press and hold the RESET button until ON or tion, press and hold the RESET button until OFF, 30 sec, OFF appears.
Page 205: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
UNDERSTANDING YOUR INSTRUMENT PANEL 203 SALES CODE REQ — AM/FM STEREO RADIO Operating Instructions - Radio Mode AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX NOTE: The ignition switch must be in the ON or ACC JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With listenable station in AM/FM mode. Press the right switch UConnect”...
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 208 206 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob a fifth time time and MID will display. Turn the TUNE/SCROLL and FADE will display. Turn the TUNE/SCROLL control control knob to the right or left to increase or decrease the knob to the left or right to adjust the sound level between mid-range tones.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 Toggle the MUSIC TYPE button to select the following 16-Digit Character Program Type format types: Display 16-Digit Character Personality Persnlty Program Type Display Public Public No program type or un- Rhythm and Blues R & B None defined Religious Music...
Page 210 208 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the Music Type icon DVD Enter - When the disc is in DVD Menu mode, is displayed, the radio will be tuned to the next frequency selecting DVD Enter will allow you to play the current station with the same selected Music Type name.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Angle – Repeatedly pressing SELECT will change Set Home Clock - Pressing the SELECT button allows the viewing angle if supported by the DVD disc (if you to set the clock. Turn the TUNE/SCROLL control equipped).
Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Language — If Equipped Audio DRC — If Equipped Selecting this item allows you to choose a default audio Selecting this item allows you to limit maximum audio language (effective only if the language is supported by dynamic range.
Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 a disc is loaded, changes will not be effective. Also, the both AM and FM. This allows a total of 12 AM, 12 FM, defaults are effective only if the disc supports the and 12 Satellite (if equipped) stations to be stored into customer-preferred settings.
Page 214: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
212 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (DISC MODE for CD and NOTE: The ignition switch must be in the ON or ACC position to operate the radio. MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by LOAD Button —...
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 213 Eject Button — Ejecting Compact Disc(s) SCAN Button (CD MODE) Press the EJECT button and the pushbutton Press the SCAN button to scan through each track on the with the corresponding number (1-6) where the CD currently playing.
Page 216: Notes On Playing Mp3/Wma Files
214 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files The radio uses the following limits for file systems: The radio can play MP3/WMA files; however, acceptable Maximum number of directory levels: 8 MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the Maximum number of files: 255 following restrictions.
Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 If a disc contains multi-formats, such as CD audio and MPEG Sampling Bit Rate (kbps) MP3/WMA tracks, the radio will only play the MP3/ Specification Frequency (kHz) WMA tracks on that disc. 320, 256, 224, MPEG-1 Audio 192, 160, 128, Supported MP3/WMA File Formats...
Page 218: List Button (Disc Mode For Mp3/Wma Play)
216 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files LIST Button (DISC Mode for MP3/WMA Play) When a medium containing MP3/WMA data is loaded, Pressing the LIST button will bring up a list of all folders the radio checks all files on the medium. If the medium on the disc.
Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 217 Press and hold the INFO button again for three seconds SCAN Button (Auxiliary Mode) to return to elapsed time display. No function. Operation Instructions - Auxiliary Mode EJECT Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack, which No function.
Page 220 218 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Voice Recognition Dolby System (VR) (If Equipped) Manufactured under license from Dolby Laboratories. For the radio, refer to “Voice Recognition System (VR)” in Dolby and the double-D symbol are trademarks of Section 3. Dolby Laboratories.
Page 221: Am/Fm/Cd/Dvd Multimedia System Radio (Rer/Ren) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 219 AM/FM/CD/DVD MULTIMEDIA SYSTEM RADIO Operating Instructions — Hands-Free (RER/REN) – IF EQUIPPED Communication (UConnect ) — If Equipped Refer to “Hands-Free Communication (UConnect )” in NOTE: The sales code is located on the lower right side Section 3.
Page 222 220 UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 6. To save the new time setting, touch the screen where the word “Save” is displayed. 1. Turn on the multimedia system. Changing Daylight Savings Time 2. Touch the screen where the time is displayed. When selected, this feature will display the time of day in 3.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 221 Show Time if Radio is Off Changing the Time Zone When selected, this feature will display the time of day 1. Turn on the multimedia system. on the touch screen when the multimedia system is turned off.
Page 224: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
222 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 223 SEEK Buttons 3. After adjusting the hours, press the right side Tune/ Press and release the SEEK buttons to search for the next Scroll control knob to set the minutes. The minutes will listenable station in AM/FM mode. Press the right switch begin to blink.
Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Push the rotary Tune/Scroll control knob a fifth time and Push the rotary Tune/Scroll control knob and BASS will FADE will display. Turn the Tune/Scroll control knob to display. Turn the Tune/Scroll control knob to the right or the left or right to adjust the sound level between the left to increase or decrease the bass tones.
Page 227: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 225 You may add a second station to each pushbutton by Operation Instructions — CD MODE For CD And repeating the above procedure with this exception: Press MP3 Audio Play the SET/RND button twice and SET 2 will show in the NOTE: display window.
Page 228 226 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
Page 229: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 227 the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD, MP3 modes. Random Play.
Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) exceeding 20 folders will result in this display. With The medium formats supported by the radio are ISO 9660 200 files, exceeding 50 folders will result in this Level 1 and Level 2 and includes the Joliet extension. display.) When reading discs recorded using formats other than Maximum number of characters in file/folder names:...
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 320, 256, 224, extension may cause playback problems.
Page 232: Operation Instructions - Auxiliary Mode
230 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or cassette player, and utilize the vehicle’s...
Page 233: Sales Code Res/Rsc - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 231 SALES CODE RES/RSC — AM/FM STEREO Operating Instructions — Radio Mode RADIO WITH CD PLAYER (MP3 AUX JACK) AND NOTE: The ignition switch must be in the ON or ACC SIRIUS RADIO position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons Phone Button (UConnect Hands-Free Phone) — If Press and release the SEEK buttons to search for the next Equipped listenable station in AM/FM mode. Press the right switch Press this button to operate the Hands-Free Phone to seek up and the left switch to seek down.
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 233 3. After adjusting the hours, press the right side Tune/ INFO Button Scroll control knob to set the minutes. The minutes will Press the INFO button for an RDS station (one with call begin to blink. letters displayed).
Page 236 234 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary Tune/Scroll control knob a second time MUSIC TYPE Button and MID will display. Turn the Tune/Scroll control knob Pressing this button once will turn on the Music Type to the right or left to increase or decrease the mid-range mode for five seconds.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 235 16-Digit Character 16-Digit Character Program Type Program Type Display Display Foreign Language Language Sports Sports Information Inform Talk Talk Jazz Jazz Top 40 Top 40 News News Weather Weather Nostalgia Nostalga By pressing the SEEK button when the Music Type icon Oldies Oldies is displayed, the radio will be tuned to the next frequency...
Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button SET/RND button, the station will continue to play but Pressing the SETUP button allows you to select between will not be stored into pushbutton memory. the following items: You may add a second station to each pushbutton by Set Clock —...
Page 239: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 237 DISC/AUX Button radio display. If a CD does not go into the slot more than Pressing the DISC/AUX button will allow you to switch 1.0 in (2.5 cm), a disc may already be loaded and must be from AM/FM modes to DISC/AUX mode.
Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button CAUTION! (Continued) Press the right SEEK button for the next selection on the RES is a single CD player. Do not attempt to insert CD. Press the left SEEK button to return to the beginning a second CD if one is already loaded.
Page 241: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 239 AM/FM Button Supported Media (Disc Types) Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. SET/RND Button (Random Play Button) Press this button while the CD is playing to activate Supported Medium Formats (File Systems) Random Play.
Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL Maximum number of folders. (The radio display of file writing are most likely multisession discs. The use of names and folder names is limited. For large numbers multisession for CD audio or MP3 playback may result in of files and/or folders, the radio may be unable to longer disc loading times.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Playback of MP3 Files MPEG Sampling Bit Rate (kbps) When a medium containing MP3 data is loaded, the Specification Frequency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128, 48, 44.1, 32...
Page 244: List Button (Cd Mode For Mp3 Play)
242 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended Press the INFO button once more to return to elapsed to use CD-R media and single-session discs. To create a time priority mode. single-session disc, enable the “Disc at Once” option Press and hold the INFO button for three seconds or before writing to the disc.
Page 245: Satellite Radio (Rsc) - If Equipped (Rer/Req/Ren Radios Only)
UNDERSTANDING YOUR INSTRUMENT PANEL 243 NOTE: The AUX device must be turned on and the SATELLITE RADIO (RSC) — IF EQUIPPED device’s volume set to proper level. If the AUX audio is (RER/REQ/REN RADIOS ONLY) not loud enough, turn the device’s volume up. If the AUX Satellite radio uses direct satellite to receiver broadcast- audio sounds distorted, turn the device’s volume down.
Page 246: Electronic Serial Number/Sirius Identification Number (Ens/Sid)
244 UNDERSTANDING YOUR INSTRUMENT PANEL 1. The Electronic Serial Number/Sirius Identification Selecting Satellite Mode Number (ESN/SID). Press the SAT button until SAT appears in the display. A CD may remain in the radio while in the Satellite radio 2. Your Vehicle Identification Number. mode.
Page 247: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 245 Reception Quality SEEK Buttons Satellite reception may be interrupted due to one of the Press and release the SEEK buttons to search for the next following reasons: channel in Satellite mode. Press the right switch to seek up and the left switch to seek down.
Page 248 246 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button turning the TUNE control knob within 5 seconds will Pressing the INFO button will cycle between Artist, Song allow the program format type to be selected. Title, and Composer (if available) information. Also, Toggle the MUSIC TYPE button again to select the music pressing and holding the INFO button for an additional type.
Page 249: Operating Instructions - Hands Free Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 247 SET Button — To Set the Push-Button Memory Every time a preset button is used, a corresponding When you are receiving a channel that you wish to button number will display. commit to push-button memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 250: Remote Sound System Controls - If Equipped
248 UNDERSTANDING YOUR INSTRUMENT PANEL REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. The left and right controls are rocker-type switches with a pushbutton in the center of each switch.
Page 251: Left-Hand Switch Functions For Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 249 Left-Hand Switch Functions for Radio Operation Press the switch up or down twice to listen to the second track, three times to listen to the third track, Press the top of the switch to SEEK the next listenable and so forth.
Page 252: Radio Operation And Cellular Phones
250 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Do not expose the disc to direct sunlight. CLIMATE CONTROLS The Air Conditioning and Heating System is designed to 7. Do not store the disc where temperatures may become make you comfortable in all types of weather. too high.
Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 251 Blower Control Temperature Control Rotate this control to regulate the Rotate this control to regulate the tem- amount of air forced through the ven- perature of the air inside the passenger tilation system in any mode. The compartment.
Page 254 252 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) NOTE: For all settings except full cold or full hot, there Rotate this control to choose from sev- is a difference in temperature between the upper and eral patterns of air distribution. You lower outlets.
Page 255 UNDERSTANDING YOUR INSTRUMENT PANEL 253 Defrost will cause the LED in the control button to illuminate. Air is directed through the windshield and side After ten minutes, the system will return to normal mode window demist outlets. Use this mode with maxi- function and the LED will turn off.
Page 256: Automatic Temperature Control (Atc) - If Equipped
254 UNDERSTANDING YOUR INSTRUMENT PANEL When the ignition switch is turned to the LOCK ECONOMY MODE position, the recirculation feature will be cancelled. If economy mode is desired, press the A/C button to turn OFF the indicator light and the A/C compressor. Then, Air Conditioning Control move the temperature control to the desired temperature.
Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 Automatic Operation NOTE: The AUTO position performs best for front seat The Infrared Climate Control System automatically occupants only. maintains the climate in the cabin of the vehicle at the 2. Dial in the temperature you would comfort levels desired by the driver and passenger.
Page 258 256 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Blower Control The temperature setting can be adjusted at anytime For full automatic operation or for without affecting automatic operation. automatic blower operation turn the knob to AUTO position. In manual Pressing the Air Conditioning Control button while in mode there are six blower speeds that AUTO mode will cause the LED in the control button can be individual selected.
Page 259 UNDERSTANDING YOUR INSTRUMENT PANEL 257...
Page 260 258 UNDERSTANDING YOUR INSTRUMENT PANEL The operator can override the AUTO mode setting to Floor change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 261 UNDERSTANDING YOUR INSTRUMENT PANEL 259 Air Conditioner Control NOTE: Press this button to turn on the air conditioning When the ignition switch is turned to the LOCK during manual operation only. When the air con- position, the recirculation feature will be cancelled. ditioning is turned on, cool dehumidified air will In cold weather, use of the Recirculation mode may lead flow through the outlets selected with the Mode control...
Page 262: Operating Tips
260 UNDERSTANDING YOUR INSTRUMENT PANEL Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation Button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 263 UNDERSTANDING YOUR INSTRUMENT PANEL 261 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 264 262 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 265 STARTING AND OPERATING CONTENTS Starting Procedures ....267 Brake/Transaxle Interlock System ..272 Normal Starting .
Page 266 264 STARTING AND OPERATING Traction ......279 Brake Assist System (BAS) ....293 Driving Through Water .
Page 267 STARTING AND OPERATING 265 Tread Wear Indicators ....312 Reformulated Gasoline ....327 Life Of Tire .
Page 268 266 STARTING AND OPERATING Starting ......333 Trailer Towing ......339 Cruising Range .
Page 269: Starting Procedures
STARTING AND OPERATING 267 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both Be sure to turn off the engine and remove the key inside and outside mirrors, and fasten your seat belt. from the ignition switch if you want to rest or Make sure all occupants have securely fastened their seat sleep in your car.
Page 270: Tip Start Feature
268 STARTING AND OPERATING Tip Start Feature If Engine Fails to Start Do not press the accelerator. Turn the ignition key briefly WARNING! to START position, and release it. The starter motor will continue to run, and it will disengage automatically Never pour fuel or other flammable liquid into the when the engine is running.
Page 271: After Starting
STARTING AND OPERATING 269 release it as soon as the starter engages. The starter motor WARNING! (Continued) will disengage automatically in 10 seconds. Once this Do not attempt to push or tow your vehicle to get occurs, release the accelerator pedal, turn the ignition it started.
Page 272: Engine Block Heater - If Equipped
270 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSAXLE The engine block heater warms the engine, and permits CAUTION! quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a Damage to the transaxle may occur if the following grounded, three-wire extension cord.
Page 273 STARTING AND OPERATING 271 WARNING! WARNING! (Continued) Unintended movement of a vehicle could injure It is dangerous to move the shift lever out of or if those in and near the vehicle. As with all vehicles, the engine speed is higher than idle speed. If your you should never exit a vehicle while the engine is foot is not firmly on the brake pedal, the vehicle running.
Page 274: Brake/Transaxle Interlock System
272 STARTING AND OPERATING Brake/Transaxle Interlock System Remove the cup holder liner. This system prevents you from moving the shift lever out Insert a key, screwdriver, or finger into the hole at the of PARK and into any gear unless the brake pedal is front of the cup holder and push and hold the manual pressed.
Page 275: Automatic Transaxle Ignition Interlock System
STARTING AND OPERATING 273 Automatic Transaxle Ignition Interlock System This system prevents the key from being removed unless the shift lever is in PARK. It also prevents shifting out of PARK unless the key is in the ON position, and the brake pedal is applied.
Page 276 274 STARTING AND OPERATING Gear Ranges WARNING! PARK Never use PARK as a substitute for the parking Supplements the parking brake by locking the transaxle. brake. Always apply parking brake fully when The engine can be started in this range. Never attempt to parked to guard against vehicle movement and pos- use PARK while vehicle is in motion.
Page 277 STARTING AND OPERATING 275 NEUTRAL conditions, reducing shifting by selecting the appropriate Engine may be started in this range. gear in AutoStick will improve the performance and extend transmission life by reducing excessive shifting WARNING! and heat build-up. DRIVE – 4 Speed Transaxle Do not coast in NEUTRAL and never turn off the This range should be used for most city and highway ignition to coast down a hill.
Page 278 276 STARTING AND OPERATING DRIVE 3 — 4 Speed Transaxle CAUTION! This range eliminates shifts into fourth gear. The trans- axle will operate normally in first and second gear. Shifts If the transaxle operating temperature exceeds ac- into third gear may be delayed to provide second gear ceptable limits, the vehicle computer will override operation at higher speeds.
Page 279: Autostick - If Equipped
STARTING AND OPERATING 277 In the event of a momentary problem, the transaxle can AUTOSTICK — IF EQUIPPED be reset to regain all forward gears by performing the AutoStick is a driver-interactive transaxle that offers six following steps: manual ratio changes to provide you with more control of the vehicle.
Page 280: General Information
278 STARTING AND OPERATING NOTE: In Autostick mode, the transaxle will only shift The transaxle will automatically shift up when maximum up or down when the driver moves the shift lever to the engine speed is reached while Autostick is engaged. Right (+) or Left (-).
Page 281: Driving On Slippery Surfaces
STARTING AND OPERATING 279 DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 282: Driving Through Water
280 STARTING AND OPERATING DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through centimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 283 STARTING AND OPERATING 281 CAUTION! (Continued) WARNING! Driving through standing water may cause dam- Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph ways inspect your vehicle’s fluids (i.e., engine oil, (8 km/h) when driving through standing water.
Page 284: Power Steering
282 STARTING AND OPERATING POWER STEERING WARNING! The standard power steering system will give you good vehicle response and increased ease of maneuverability Continued operation with reduced power steering in tight spaces. The system will provide mechanical assist could pose a safety risk to yourself and others. steering capability if power assist is lost.
Page 285: Parking Brake
STARTING AND OPERATING 283 apparent, and/or the system is not functioning as antici- PARKING BRAKE pated. Coordinate inspection efforts through an autho- The parking brake should always be applied when the rized dealer. driver is not in the vehicle. No chemical flushes should be used in any power WARNING! steering system;...
Page 286 284 STARTING AND OPERATING As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. To apply the parking brake, grasp the handle and pull it upward until you feel resistance. To release the parking brake, grasp the handle and pull it slightly while pressing the button on the end of the handle.
Page 287: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 285 If the parking brake is applied while the vehicle is WARNING! moving, a chime will sound to alert the driver. The chime will sound up to 10 times or until the vehicle Never leave children alone in a vehicle. Leaving has returned to a stop.
Page 288 286 STARTING AND OPERATING WARNING! WARNING! (Continued) The capabilities of an ABS equipped vehicle must Pumping of the Anti-Lock Brakes will diminish never be exploited in a reckless or dangerous their effectiveness and may lead to an accident. manner, which could jeopardize the user’s safety Pumping makes the stopping distance longer.
Page 289 STARTING AND OPERATING 287 If the ABS light is on, the brake system should be serviced ABS is activated during braking under certain road or as soon as possible to restore the benefits of Anti-Lock stopping conditions. ABS-inducing conditions can in- brakes.
Page 290: Brake System
288 STARTING AND OPERATING BRAKE SYSTEM WARNING! Your vehicle is equipped with dual hydraulic brake systems. If either of the two hydraulic The Anti-Lock Brake System contains sophisticated systems loses normal capability, the remaining electronic equipment that may be susceptible to system will still function.
Page 291: Anti-Lock Brake System - If Equipped
STARTING AND OPERATING 289 Anti-Lock Brake System — If Equipped WARNING! The Anti-Lock Brake System (ABS) provides increased vehicle stability and brake performance under most Riding the brakes can lead to brake failure and braking conditions. The system automatically “pumps” possibly an accident.
Page 292 290 STARTING AND OPERATING You also may experience the following when the brake WARNING! system goes into Anti-lock: The ABS contains sophisticated electronic equip- The ABS motor running (it may continue to run for a ment that may be susceptible to interference short time after the stop), caused by improperly installed or high output The clicking sound of solenoid valves,...
Page 293 STARTING AND OPERATING 291 Anti-Lock Brake Light WARNING! (Continued) The Anti-Lock Brake Light monitors the ABS. The ABS cannot prevent the natural laws of phys- The light will come on when the ignition ics from acting on the vehicle, nor can it increase switch is turned to the ON position and may braking or steering efficiency beyond that af- stay on for as long as four seconds.
Page 294: Electronic Brake Control System
292 STARTING AND OPERATING If both the Brake System Warning Light and the Anti- help avoid skidding on slippery surfaces during braking. Lock Brake Light remain on, the ABS and Electronic Refer to “Anti-Lock Brake System” in this Section of the Brake Force Distribution (EBD) systems are not function- manual for more information about ABS.
Page 295: Brake Assist System (Bas)
STARTING AND OPERATING 293 Brake Assist System (BAS) WARNING! The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The BAS cannot prevent the natural laws of physics system detects an emergency braking situation by sens- from acting on the vehicle, nor can it increase ing the rate and amount of brake application and then braking efficiency beyond that afforded by the...
Page 296: Electronic Stability Program (Esp)
294 STARTING AND OPERATING Electronic Stability Program (ESP) ESP/TCS Indicator Light The “ESP/TCS Indicator Light, located in the instrument This system enhances directional control and stability of cluster, starts to flash as soon as the tires lose traction and the vehicle under various driving conditions. ESP cor- the ESP system becomes active.
Page 297 STARTING AND OPERATING 295 This mode should be used for almost all driving situa- WARNING! (Continued) tions. ESP should only be turned to Partial Off for specific ESP cannot prevent accidents, including those reasons as noted below. resulting from excessive speed in turns, driving on Partial ESP Mode very slippery surfaces, or hydroplaning.
Page 298 296 STARTING AND OPERATING ESP/BAS Warning Light and ESP/TCS Indicator WARNING! Light The malfunction indicator for the ESP is com- In the Partial ESP mode, the engine torque reduction bined with the BAS indicator. The yellow ESP/ and stability features are desensitized. Therefore, the BAS Warning Light and the yellow ESP/TCS enhanced vehicle stability offered by ESP is unavail- Indicator Light in the instrument cluster both...
Page 299: Tire Safety Information
STARTING AND OPERATING 297 NOTE: TIRE SAFETY INFORMATION The ESP Indicator Light and the ESP/BAS Warning Tire Markings Light come on momentarily each time the ignition switch is turned ON. Each time the ignition is turned ON, the ESP System will be ON even if it was turned off previously.
Page 300 298 STARTING AND OPERATING NOTE: tires is the same as for P-Metric tires except for the P (Passenger) - Metric tire sizing is based on U.S. letters “LT” that are molded into the sidewall preced- design standards. P-Metric tires have the letter “P” ing the size designation.
Page 301 STARTING AND OPERATING 299 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm)
Page 302 300 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 303: Tire Identification Number (Tin)
STARTING AND OPERATING 301 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 304: Tire Loading And Tire Pressure
302 STARTING AND OPERATING Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
Page 305 STARTING AND OPERATING 303 NOTE: Under a maximum loaded vehicle condition, Steps for Determining Correct Load Limit gross axle weight ratings (GAWRs) for the front and rear 1. Locate the statement “The combined weight of occu- axles must not be exceeded. For further information on pants and cargo should never exceed XXX lbs or XXX kg”...
Page 306 304 STARTING AND OPERATING 4. The resulting figure equals the available amount of manual to determine how this reduces the available cargo and luggage load capacity. For example, if “XXX” cargo and luggage load capacity of your vehicle. amount equals 1,400 lbs (635 kg) and there will be five NOTE: 150 lb (68 kg) passengers in your vehicle, the amount of The following table shows examples on how to calcu-...
Page 307 STARTING AND OPERATING 305...
Page 308: Tires - General Information
306 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle. Never Under inflation increases tire flexing and can result overload them.
Page 309: Tire Inflation Pressures
STARTING AND OPERATING 307 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the Unequal tire pressures from one side of the vehicle driver’s side “B” Pillar. to the other can cause the vehicle to drift to the right Some vehicles may have Supplemental Tire Pressure or left.
Page 310 308 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12° F (7° C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
Page 311: Radial-Ply Tires
STARTING AND OPERATING 309 Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 312: Compact Spare Tire - If Equipped
310 STARTING AND OPERATING Compact Spare Tire — If Equipped CAUTION! The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style Prolonged use of limited use spare, or an incorrect vehicle only.
Page 313: Limited Use Spare - If Equipped
STARTING AND OPERATING 311 Limited Use Spare — If Equipped WARNING! The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use The limited use spare tires are for emergency use spare tire warning label located on the limited use spare only.
Page 314: Tire Spinning
312 STARTING AND OPERATING Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels faster than 30 mph (48 km/h) to help you in determining when your tires should be or for longer than 30 seconds continuously without replaced.
Page 315: Life Of Tire
STARTING AND OPERATING 313 These indicators are molded into the bottom of the tread WARNING! grooves. They will appear as bands when the tread depth becomes approximately 1/16 in (2 mm). When the tread Tires and spare tire should be replaced after six years, is worn to the tread wear indicators, the tire should be regardless of the remaining tread.
Page 316 314 STARTING AND OPERATING Information” placard for the size designation of your tire. WARNING! The service description and load identification will be found on the original equipment tire. Failure to use Do not use a tire, wheel size or rating other than equivalent replacement tires may adversely affect the that specified for your vehicle.
Page 317: Tire Chains
STARTING AND OPERATING 315 WARNING! (Continued) CAUTION! Failure to equip your vehicle with tires having Damage to the vehicle may result if tire chains are adequate speed capability can result in sudden tire used. failure and loss of vehicle control. SNOW TIRES CAUTION! Some areas of the country require the use of snow tires...
Page 318: Tire Rotation Recommendations
316 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates and tend to develop irregular wear pat- terns.
Page 319: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 317 TIRE PRESSURE MONITOR SYSTEM (TPMS) pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment for this The Tire Pressure Monitor System (TPMS) will warn increased pressure. the driver of a low tire pressure based on the vehicle recommended cold placard pressure.
Page 320 318 STARTING AND OPERATING once the system receives the updated tire pressures. CAUTION! The vehicle may need to be driven for up to 20 minutes above 15 mph (25 km/h) in order for the TPMS to The TPMS has been optimized for the original receive this information.
Page 321: Base System
STARTING AND OPERATING 319 NOTE: Seasonal temperature changes will affect tire pressure, The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire.
Page 322 320 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings repeat, providing the system fault still exists. The Tire The Tire Pressure Monitoring Telltale Light will Pressure Monitoring Telltale Light will turn off when the illuminate in the instrument cluster and a chime fault condition no longer exists.
Page 323: Premium System - If Equipped
STARTING AND OPERATING 321 NOTE: Light will turn OFF, as long no tire pressure is below the 1. The compact spare tire (if so equipped) does not have low-pressure warning limit in any of the four active road a tire pressure monitoring sensor. Therefore, the TPMS tires.
Page 324 322 STARTING AND OPERATING Three Trigger Modules (mounted in three of the four wheel-wells) Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster and a chime will sound when tire pressure is low in one or...
Page 325 STARTING AND OPERATING 323 Should this occur, you should stop as soon as possible, and inflate all tires with low pressure (those flashing in the EVIC graphic) to the vehicle’s recommended cold placard pressure value. Once the system receives the updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flash- ing, and the Tire Pressure Monitoring Telltale Light will...
Page 326 324 STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to Light will remain ON, a chime will sound, and the EVIC facilities emitting the same Radio Frequencies as the TPM will still display a flashing pressure value in the graphic sensors.
Page 327: General Information
STARTING AND OPERATING 325 5. Once you repair or replace the original road tire, and The tire pressure sensors are covered under one of the reinstall it on the vehicle in place of the compact spare, following licenses: the TPMS will update automatically. In addition, the TPM Telltale Light will turn OFF and the graphic in the United States .
Page 328: 3.5L Engine
326 STARTING AND OPERATING 3.5L Engine Poor quality gasoline can cause problems such as hard The 3.5L engine is designed to meet all starting, stalling, and hesitations. If you experience these emissions regulations and provide satisfac- symptoms, try another brand of gasoline (with the ap- tory fuel economy and performance when propriate octane rating for your engine) before consider- using high-quality unleaded gasoline hav-...
Page 329: Reformulated Gasoline
STARTING AND OPERATING 327 Reformulated Gasoline CAUTION! Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Etha- Reformulated gasolines contain oxygenates, and are spe- nol.
Page 330: E-85 Usage In Non-Flex Fuel Vehicles
328 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles disconnect and reconnect the battery to reset the Non-FFV vehicles are compatible with gasoline contain- engine controller memory ing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty.
Page 331: Materials Added To Fuel
STARTING AND OPERATING 329 It is even more important to look for gasolines without The use of leaded gas is prohibited by Federal law. MMT in Canada, because MMT can be used at levels Using leaded gasoline can impair engine performance higher than those allowed in the United States.
Page 332: Carbon Monoxide Warnings
330 STARTING AND OPERATING Carbon Monoxide Warnings the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side WARNING! windows fully open. Keep the trunk closed when driving your vehicle to Carbon monoxide (CO) in exhaust gases is deadly. prevent carbon monoxide and other poisonous ex- Follow the precautions below to prevent carbon haust gases from entering the vehicle.
Page 333 STARTING AND OPERATING 331 Along with the special E-85 fuel filler cap, your vehicle may display a badge, which also indicates it can operate on E-85. E-85 Fuel Cap CAUTION! Only vehicles with the special E-85 fuel filler cap can E-85 Badge operate on E-85.
Page 334: Ethanol Fuel (E-85)
332 STARTING AND OPERATING ETHANOL FUEL (E-85) For best results, a refueling pattern that avoids alternat- E-85 is a mixture of approximately 85% fuel ethanol and ing between E-85 and unleaded gasoline is recom- 15% unleaded gasoline. mended. When you do switch fuel types it is recommended that: WARNING! you do not add less than 5 gal (19 L) when refueling Ethanol vapors are extremely flammable and could...
Page 335: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
MOPAR engine oils, and in equivalent oils meeting increase in the time it takes for your engine to start, and Chrysler Specification MS-6395. The manufacturer only a deterioration in driveability (sags and/or hesitations) recommends engine oils that are API Certified and meet until the engine is fully warmed up.
Page 336: 334 Starting And Operating
334 STARTING AND OPERATING The gas cap is behind the fuel filler door, on the left rear CAUTION! quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this Replacing fuel system components with non-ethanol vehicle.
Page 337 STARTING AND OPERATING 335 After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the gas cap suspended away from and protects the vehicle’s Damage to the fuel system or emission control surface.
Page 338: Loose Filler Cap Message
336 STARTING AND OPERATING When the fuel nozzle “clicks” or shuts off, the fuel WARNING! (Continued) tank is full. Never add fuel when the engine is running. This is Loose Filler Cap Message in violation of most state and federal fire regula- If the vehicles diagnostic system determines that the fuel tions and doing so will cause the malfunction filler cap in loose, improperly installed, or damaged, a...
Page 339: Vehicle Loading
STARTING AND OPERATING 337 VEHICLE LOADING The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Vehicle Certification Label Your vehicle has a certification label attached to the rear Gross Vehicle Weight Rating (GVWR) of the driver’s door. The GVWR is the total allowable weight of your vehicle.
Page 340: Overloading
338 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle WARNING! separately. It is important that you distribute the load evenly over the front and rear axles. Because the front wheels steer the vehicle, it is important that you do not exceed the maximum front Overloading can cause potential safety hazards and or rear GAWR.
Page 341: Trailer Towing
STARTING AND OPERATING 339 TRAILER TOWING Gross Vehicle Weight Rating (GVWR) In this section, you will find safety tips and information The GVWR is the total allowable weight of your vehicle. on limits to the type of towing you can reasonably do This includes driver, passengers, cargo, and tongue with your vehicle.
Page 342 340 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Frontal Area The GAWR is the maximum capacity of the front and rear The frontal area is the maximum height and maximum axles. Distribute the load over the front and rear axles width of the front of a trailer and its cargo.
Page 343: Trailer Hitch Classification
STARTING AND OPERATING 341 Trailer Hitch Classification Trailer Hitch Classification The following chart provides the industry standard for Max. GTW Class the maximum trailer weight a given trailer hitch class can (Gross Trailer Wt.) tow and should be used to assist you in selecting the Class I - Light Duty 2,000 lbs (907 kg) correct trailer hitch for your intended towing condition.
Page 344: Trailer Towing Weights (Maximum Trailer Weight Ratings)
Tire cylinder and 2.7L engines with automatic transaxle. and Loading Information placard. Refer to “Tire Safety Please refer to the following website, http://www- Information” in Section 5 of this manual. 5.chrysler.com/searchapp/ui.jsp or your authorized dealer for additional information.
Page 345: Trailer And Tongue Weight
STARTING AND OPERATING 343 CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme condi- tions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 346: Towing Requirements
344 STARTING AND OPERATING NOTE: Remember that everything put into or on the Towing Requirements trailer adds to the load on your vehicle. Also, additional To promote proper break-in of your new vehicle driv- factory-installed options, or authorized dealer-installed etrain components the following guidelines are recom- options, must be considered as part of the total load on mended: your vehicle.
Page 347 STARTING AND OPERATING 345 Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the Improper towing can lead to an injury accident. chains under the trailer tongue and allow enough Follow these guidelines to make your trailer tow- slack for turning corners.
Page 348 346 STARTING AND OPERATING 4. Trailer tongue weight rating for the trailer hitch When replacing tires, refer to “Tires — General Infor- utilized (This requirement may limit the ability to mation” in this section for information on replacement always achieve 10% of trailer tongue weight as a tires and for proper tire replacement procedures.
Page 349: Towing Tips
STARTING AND OPERATING 347 Trailer brakes are recommended for trailers over WARNING! (Continued) 1,000 lbs (450 kg) and required for trailers in excess of Towing any trailer will increase your stopping 2,000 lbs (907 kg). distance. When towing, you should allow for ad- ditional space between your vehicle and the ve- CAUTION! hicle in front of you.
Page 350 348 STARTING AND OPERATING Automatic Transaxle NOTE: Check the four-speed automatic transaxle fluid The DRIVE range can be selected when towing. How- level before towing. AutoStick six—speed transmission ever, if frequent shifting occurs while in this range, third is sealed and the fluid level cannot be checked. See your gear for a four-speed automatic and the fifth gear for a authorized dealership service center for assistance.
Page 351: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 349 Cooling System RECREATIONAL TOWING (BEHIND To reduce potential for engine and transaxle overheating, MOTORHOME, ETC.) take the following actions: Towing This Vehicle Behind Another Vehicle (Flat City Driving towing with all four wheels on the ground) When stopped for short periods of time, put transaxle in CAUTION! neutral and increase engine idle speed.
Page 353 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....352 Jacking Instructions ....356 If Your Engine Overheats .
Page 354: Hazard Warning Flasher
352 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER NOTE: With extended use, the Hazard Warning flasher The Hazard Warning flasher switch is located in the may wear down your battery. instrument panel switch bank above the climate controls. IF YOUR ENGINE OVERHEATS Press the switch to turn on the Hazard In any of the following situations, you can reduce the Warning flashers.
Page 355: What To Do In Emergencies 353
WHAT TO DO IN EMERGENCIES 353 the fan control to High. This allows the heater core to act WARNING! as a supplement to the radiator and aids in removing heat from the engine cooling system. A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling CAUTION! coolant.
Page 356: Jacking And Tire Changing
354 WHAT TO DO IN EMERGENCIES NOTE: Engine speed is reduced to 53 mph (85 km/h) at WARNING! (Continued) the maximum. You may of course, reduce your speed The jack is designed to use as a tool for changing further if needed. tires only.
Page 357: Jack Location
WHAT TO DO IN EMERGENCIES 355 6. Block both the front and rear of the Spare Tire Removal wheel diagonally opposite the jacking Lift up the load floor cover and remove the hold down. position. For example, if changing the right front tire, block the left rear wheel.
Page 358: Jacking Instructions
356 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! (Continued) Do not let anyone sit in the vehicle when it is on a WARNING! jack. Carefully follow these tire changing warnings to Do not get under the vehicle when it is on a jack. help prevent personal injury or damage to your Only use the jack in the positions indicated and vehicle:...
Page 359 WHAT TO DO IN EMERGENCIES 357 Jack Warning Label 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.
Page 360 358 WHAT TO DO IN EMERGENCIES Jacking Locations...
Page 361 WHAT TO DO IN EMERGENCIES 359 head is properly engaged with the lift area closest to the CAUTION! wheel to be changed. Do not raise the vehicle until you are sure the jack is securely engaged. Do not attempt to raise the vehicle by jacking on locations other than those indicated in Step 3.
Page 362 360 WHAT TO DO IN EMERGENCIES 6. Remove the wheel nuts, and pull the wheel and wheel 8. Finish tightening the nuts. Push down on the wrench covers (if equipped) off the hub. Install the spare wheel while tightening the wheel nuts. Alternate nuts, until and wheel nuts with the cone shaped end of the nuts each nut has been tightened twice.
Page 363: Jump-Starting Procedure
WHAT TO DO IN EMERGENCIES 361 10. Place the deflated (flat) tire in the cargo area, have the WARNING! (Continued) tire repaired or replaced as soon as possible. Do not attempt to push or tow your vehicle to get 11. Check the spare tire pressure as soon as possible. it started.
Page 364 362 WHAT TO DO IN EMERGENCIES 2. When boosting from a battery in another vehicle, park 4. Remove the protective cover over the remote jump- that vehicle within booster cable reach, but without start positive battery post (+) in the engine compartment. allowing the vehicles to touch.
Page 365 WHAT TO DO IN EMERGENCIES 363 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the se- quence exactly.
Page 366: Freeing A Stuck Vehicle
364 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Maintenance Procedures” in Section 7 FREEING A STUCK VEHICLE of this manual for information on accessing the battery If your vehicle becomes stuck in mud, sand, or snow, it for service or replacement. can often be moved by a rocking motion.
Page 367: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 365 TOWING A DISABLED VEHICLE WARNING! With The Ignition Key Fast spinning tires can be dangerous. Forces gener- Your vehicle may be towed under the following condi- ated by excessive wheel speeds may cause axle and tions: The shift lever must be in NEUTRAL, the distance tire damage or failure.
Page 368: Without The Ignition Key
366 WHAT TO DO IN EMERGENCIES Without The Ignition Key CAUTION! (Continued) Special care must be taken when the vehicle is towed Do not attempt to tow this vehicle from the front with the ignition in the LOCK position. Flat bed towing with sling type towing equipment.
Page 369: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.4L ... . . 369 Maintenance Procedures ....376 Engine Compartment —...
Page 370 368 MAINTAINING YOUR VEHICLE Windshield Washers ....385 Replacement Bulbs ....411 Exhaust System .
Page 371: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 369 ENGINE COMPARTMENT — 2.4L 1 — Engine Coolant Reservoir 7 — Air Cleaner Filter 2 — Power Steering Fluid Reservoir 8 — Engine Oil Fill 3 — Automatic Transaxle Dipstick 9 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 10 —...
Page 372: Engine Compartment - 2.7L
370 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.7L 1 — Engine Coolant Reservoir 7 — Power Distribution Center 2 — Coolant Pressure Cap 8 — Air Cleaner Filter 3 — Power Steering Fluid Reservoir 9 — Engine Oil Dipstick 4 — Automatic Transaxle Dipstick 10 —...
Page 373: Engine Compartment - 3.5L
MAINTAINING YOUR VEHICLE 371 ENGINE COMPARTMENT — 3.5L 1 — Engine Coolant Reservoir 6 — Air Cleaner Filter 2 — Coolant Pressure Cap 7 — Engine Oil Dipstick 3 — Power Steering Fluid Reservoir 8 — Engine Oil Fill 4 — Brake Fluid Reservoir 9 —...
Page 374: Onboard Diagnostic System - Obd Ii
372 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 375: Loose Fuel Filler Cap Message
MAINTAINING YOUR VEHICLE 373 Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE After fuel is added, the vehicle diagnostic system can PROGRAMS determine if the fuel filler cap is possibly loose or In some localities, it may be a legal requirement to pass improperly installed.
Page 376 374 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, the ignition or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD II system is not ready and you should check if your vehicle’s OBD II system is ready, you must not proceed to the I/M station.
Page 377: Replacement Parts
MAINTAINING YOUR VEHICLE 375 Regardless of whether your vehicle’s OBD II system is DEALER SERVICE ready or not, if the MIL is illuminated during normal Your authorized dealer has the qualified service person- vehicle operation you should have your vehicle serviced nel, special tools, and equipment to perform all service before going to the I/M station.
Page 378: Maintenance Procedures
376 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES The best time to check the engine oil level is about The pages that follow contain the required maintenance 5 minutes after a fully warmed engine is shut off. Do not services determined by the engineers who designed your check oil level before starting the engine after it has sat vehicle.
Page 379 Do not overfill the engine. Overfilling the engine mends engine oils that are API Certified and meet the will cause oil aeration, which can lead to loss of oil requirements of Chrysler Material Standard MS-6395. pressure and an increase in oil temperature. This could damage your engine.
Page 380 378 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L Lubricants which do not have both the engine oil certi- Engines fication mark and the correct SAE viscosity grade num- SAE 5W-20 engine oil is recommended for all operating ber should not be used.
Page 381: Engine Oil Filter
MAINTAINING YOUR VEHICLE 379 Materials Added to Engine Oils Engine Oil Filter The manufacturer strongly recommends against the ad- The engine oil filter should be replaced at every engine dition of any additives (other than leak detection dyes) to oil change. the engine oil.
Page 382: Engine Air Cleaner Filter
380 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Engine Air Cleaner Filter Selection The quality of replacement engine air cleaner filters WARNING! varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR engine air The air induction system (air cleaner, hoses, etc.) can cleaner filters are high quality and are recommended.
Page 383 MAINTAINING YOUR VEHICLE 381 WARNING! CAUTION! Battery fluid is a corrosive acid solution and can It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 384: Air Conditioner Maintenance
382 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner The air conditioning system contains refrigerant should be checked and serviced by an authorized dealer under high pressure. To avoid risk of personal at the start of each warm season. This service should injury or damage to the system, adding refrigerant include cleaning of the condenser fins and a performance or any repair requiring lines to be disconnected...
Page 385: A/C Air Filter - If Equipped
MAINTAINING YOUR VEHICLE 383 NOTE: Use only manufacturer approved A/C System 2. Push in on the sides of the glove box and lower the Sealers, Stop Leak Products, Seal Conditioners, Compres- door. sor Oil, and Refrigerants. 3. Disconnect the glove box door dampener from the slot A/C Air Filter —...
Page 386: Body Lubrication
384 MAINTAINING YOUR VEHICLE 5. Disengage the two retaining tabs that secure the filter CAUTION! cover to the HVAC housing and remove the cover. The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often.
Page 387: Adding Washer Fluid
MAINTAINING YOUR VEHICLE 385 attention should also be given to hood latching compo- Avoid using the wiper blades to remove frost or ice from nents to insure proper function. When performing other the windshield. Make sure that they are not frozen to the underhood services, the hood latch, release mechanism glass before turning them on to avoid damaging the and safety catch should be cleaned and lubricated.
Page 388: Exhaust System
386 MAINTAINING YOUR VEHICLE exhaust system each time the vehicle is raised for an oil WARNING! change or lubrication. Replace as required. Commercially available windshield washer solvents WARNING! are flammable. They could ignite and burn you. Care must be exercised when filling or working around Exhaust gases can injure or kill.
Page 389 MAINTAINING YOUR VEHICLE 387 Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed portant to keep the engine properly tuned to assure against you.
Page 390: Cooling System
388 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! (Continued) Do not shut off the engine or interrupt the ignition You or others can be badly burned by hot engine when the transaxle is in gear and the vehicle is in coolant (antifreeze) or steam from your radiator.
Page 391 MAINTAINING YOUR VEHICLE 389 Check the coolant recovery bottle tubing for brittle rub- CAUTION! ber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for Mixing of engine coolant (antifreeze) other than leaks.
Page 392 390 MAINTAINING YOUR VEHICLE When adding engine coolant (antifreeze): CAUTION! (Continued) The manufacturer recommends using MOPAR This vehicle has not been designed for use with Antifreeze/Coolant 5 Year/100,000 Mile Formula Propylene Glycol based engine coolant (anti- HOAT (Hybrid Organic Additive Technology). freeze).
Page 393 MAINTAINING YOUR VEHICLE 391 NOTE: Mixing engine coolant (antifreeze) types will WARNING! decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes. The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- Cooling System Pressure Cap caution.
Page 394 392 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant 6 Cylinder Engines — the level of the engine coolant Used ethylene glycol based engine coolant (antifreeze) is (antifreeze) in the pressurized coolant bottle should be a regulated substance requiring proper disposal. Check between the “COLD”...
Page 395 MAINTAINING YOUR VEHICLE 393 Points To Remember If frequent engine coolant (antifreeze) additions are required, or if the level in the coolant recovery bottle NOTE: When the vehicle is stopped after a few miles does not drop when the engine cools, the cooling (kilometers) of operation, you may observe vapor coming system should be pressure tested for leaks.
Page 396: Brake System
394 MAINTAINING YOUR VEHICLE Do not change the thermostat for Summer or Winter Master Cylinder - Brake Fluid Level Check operation. If replacement is ever necessary, install Check the fluid level in the master cylinder immediately ONLY the correct type thermostat. Other designs may if the brake system warning light indicates system fail- result in unsatisfactory cooling performance, poor gas ure.
Page 397: Automatic Transaxle
MAINTAINING YOUR VEHICLE 395 Use only manufacturer’s recommended brake fluid. Re- Use only brake fluid that has been in a tightly closed fer to “Fluids, Lubricants, and Genuine Parts” in this container to avoid contamination from foreign matter or section for the correct fluid type. moisture.
Page 398 396 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L driven at least 15 miles (24 km). Hot fluid cannot be held Engines comfortably between the fingertips. Cold fluid is at a Use the following procedure to check the automatic temperature below 80°F (27°...
Page 399 MAINTAINING YOUR VEHICLE 397 Fluid Level Check — Vehicles with 3.5L Engine CAUTION! The automatic transaxle has no dipstick and is dealer serviced only. Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- Transmission Fluid and Filter Changes ration in transmission shift quality and/or torque Refer to the “Maintenance Schedule”...
Page 400: Appearance Care And Protection From Corrosion
398 MAINTAINING YOUR VEHICLE Appearance Care And Protection From Corrosion The most common causes are: Protection of Body and Paint from Corrosion Road salt, dirt, and moisture accumulation. Vehicle body care requirements vary according to geo- Stone and gravel impact. graphic locations and usage.
Page 401 MAINTAINING YOUR VEHICLE 399 Use MOPAR Cleaner Wax to remove road film, stains If you detect any stone chips or scratches in the paint, and to protect your paint finish. Take care never to touch them up immediately. The cost of such repairs is scratch the paint.
Page 402 400 MAINTAINING YOUR VEHICLE Wheel and Wheel Trim Care To minimize the possibility of scratching the lenses and All wheels and wheel trim, especially aluminum and reducing light output, avoid wiping with a dry cloth. To chrome plated wheels, should be cleaned regularly with remove road dirt, wash with a mild soap solution fol- a mild soap and water to prevent corrosion.
Page 403 MAINTAINING YOUR VEHICLE 401 MOPAR Spot & Stain Remover if absolutely necessary. WARNING! Do not use harsh cleaners or Armorall. Use MOPAR Total Clean to clean vinyl upholstery Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Cleaning Leather Upholstery closed areas they may cause respiratory harm.
Page 404 402 MAINTAINING YOUR VEHICLE For grease stains, apply MOPAR Multi-Purpose Cleaning Plastic Instrument Cluster Lenses Cleaner to a clean, damp cloth and remove stain. Use The lenses in front of the instruments in this vehicle are a fresh, damp towel to remove soap residue. molded in clear plastic.
Page 405: Cleaning Center Console Cupholders
MAINTAINING YOUR VEHICLE 403 Replace the belts if they appear frayed or worn or if the Installation buckles do not work properly. Align the liner in the cupholder and press down firmly. Dry with a soft tissue. Convertible Top Care Immediate removal of any contaminant is recommended.
Page 406 404 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Avoid high-pressure car washes, as they can damage Never use an abrasive type cleaner or bleaches. the top material. Also, increased water pressure may Cleaners should not contain silicones, organic sol- force water past the weather strips. vents, petroleum distillates, or plasticizers.
Page 407: Weather Strip Care - Soft & Hard Top
MAINTAINING YOUR VEHICLE 405 Additional Cleaning Procedure CAUTION! For additional cleaning assistance in removing stubborn stains, apply MOPAR Convertible Cloth Top Cleaner to Avoid getting Scotchguard on the surrounding the complete stain, extending 2 inches (50 mm) beyond weather strips, moldings, paint, or glass. Damage to the stain.
Page 408 406 MAINTAINING YOUR VEHICLE Cartridge Mini Cavity Description Fuse Fuse Battery Feed — Center High 10 Amp — Mounted Stop Light (CHMSL)/ Brake Switch 10 Amp Battery Feed — — Ignition Switch 20 Amp Trailer Tow — If — Yellow Equipped Ignition Off Totally Integrated Power Module (TIPM)
Page 409 MAINTAINING YOUR VEHICLE 407 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Off 20 Amp 30 Amp — — — Draw (IOD) Yellow Green Sense 2 Ignition Off Battery Feed — Draw (IOD) — Power Seats - if 10 Amp Cabin Compart- 40 Amp...
Page 410 408 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Off 10 Amp — — Draw (IOD) — Wireless Control Ignition Run — 10 Amp — Module (WCM)/ Climate 10 Amp Clock/Steering — Controls/Hot Control Module Cupholder - if...
Page 411 MAINTAINING YOUR VEHICLE 409 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 15 Amp Auto Shutdown Ignition Run — 20 Amp — (ASD) Relay Feed — Heated Seats - If Yellow Blue Equipped Ignition Run — 10 Amp —...
Page 412 410 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Battery Feed — Battery Feed — Anti-Lock Brakes Passenger Door 30 Amp (ABS) Module - if — Module (PDM)/ Pink 30 Amp equipped/ Driver Door —...
Page 413: Vehicle Storage
MAINTAINING YOUR VEHICLE 411 REPLACEMENT BULBS CAUTION! (Continued) All the inside bulbs are brass or glass wedge base. When replacing a blown fuse, it is important to Aluminum base bulbs are not approved and should not use only a fuse having the correct amperage rating. be used for replacement.
Page 414: Bulb Replacement
412 MAINTAINING YOUR VEHICLE NOTE: It may be necessary to remove the air cleaner LIGHT BULBS — Exterior Bulb No. filter housing and position the totally integrated power Low Beam Headlight ..... 9006 module aside prior to replacing the low beam headlight High Beam Headlight.
Page 415 MAINTAINING YOUR VEHICLE 413 3. Rotate bulb and connector one-quarter turn and pull 4. Pull the bulb out of the socket and replace the bulb. outward from assembly. 5. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. CAUTION! 6.
Page 416: Front Turn Signal/Parking Light
414 MAINTAINING YOUR VEHICLE Front Turn Signal/Parking Light 3. Remove the bulb from the connector socket and install the replacement bulb. 1. Raise and prop open the hood. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector one-quarter turn headlight housing and rotate the connector one-quarter counterclockwise and remove it from the headlight hous- turn clockwise to lock it in place.
Page 417 MAINTAINING YOUR VEHICLE 415 CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with an oily surface, clean the bulb with rubbing alcohol. 3. Install the bulb and connector assembly into the fog light housing and rotate the connector one-quarter turn clockwise to lock it in place.
Page 418: Tail/Stop, Rear Turn Signal And Backup Lights
416 MAINTAINING YOUR VEHICLE Tail/Stop, Rear Turn Signal and Backup Lights Changing the Tail/Stop Light or Rear Turn Signal The taillights are a two piece design. The turn signal, Light brake and taillights are located in the rear corner body 1.
Page 419 MAINTAINING YOUR VEHICLE 417 1 — Tail/Stop Light 2 — Turn Signal Light 3. Grasp the taillight housing and pull it firmly outward while pushing gently on the studs from inside to disen- 5. Remove the bulb from the connector socket and install gage the housing from the vehicle.
Page 420: License Plate Light
418 MAINTAINING YOUR VEHICLE Changing the Backup Light 3. Remove the bulb from the connector socket and install the replacement bulb. 1. Open the trunk. 4. Install the bulb and connector assembly into the 2. Rotate the bulb’s electrical connector one-quarter turn housing and rotate the connector one-quarter turn clock- counterclockwise and remove it from the housing.
Page 421: Center High-Mounted Stop Light (Chmsl)
MAINTAINING YOUR VEHICLE 419 2. Rotate the bulb’s electrical connector one-quarter turn counterclockwise and remove it from the CHMSL housing. 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the light 3. Remove the bulb from the connector socket and install lens with the two retaining screws.
Page 422: Fluids And Capacities
420 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 2.4L and 2.7L Engine 16.9 Gallons 64 Liters 3.5L Engine 17.2 Gallons 65 Liters Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.4 Liters 2.7L Engine (SAE 5W-20, API Certified) 5.5 Quarts 5.2 Liters 3.5L Engine (SAE 10W-30, API Certified)
Page 423: Fluids, Lubricants, And Genuine Parts
Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the en- Engine Oil (2.4L and 2.7L Engine) gine oil fill cap for the correct SAE grade meeting Chrysler Material Stan- dard MS-6395. Use API Certified engine oil. SAE 10W-30 is recommended. Refer to the Engine Oil (3.5L Engine)
Page 424 422 MAINTAINING YOUR VEHICLE Component Fluid, Lubricant, or Genuine Part Fuel Selection (2.7L Engine - EX- CEPT CALIFORNIA EMISSION E-85 Ethanol STATES) Fuel Selection (3.5L Engine) 89 Octane Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transaxle MOPAR ATF+4 Automatic Transmission Fluid MOPAR DOT 3 and SAE J1703 should be used.
Page 425: Maintenance Schedules
MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..424 Required Maintenance Intervals ..426 Maintenance Schedule ....424...
Page 426 424 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Electronic Vehicle Information Center (EVIC) system.
Page 427 MAINTENANCE SCHEDULES 425 NOTE: Settings” of the EVIC section in this manual or under The oil change indicator message will not monitor the “Odometer/Trip Odometer” in the “Instrument Cluster time since the last oil change. Change your vehicles oil Descriptions section of this manual. if it has been 6 months since your last oil change even At Each Stop for Fuel if the oil change indicator message is NOT illumi-...
Page 428 426 MAINTENANCE SCHEDULES Once a Month At Each Oil Change Check tire pressure and look for unusual wear or Change the engine oil filter. damage. Inspect the brake hoses and lines. Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 429 Inspect the exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or 12 months. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 430 Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 431 Replace the air conditioning filter (if equipped). Odometer Reading Date Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 432: Service Schedule
Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 433 Change the automatic transaxle fluid & filter if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 434 Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 435 Inspect and replace the PCV valve, if necessary. necessary†. Replace the air conditioning filter (if equipped). Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 436 Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Inspect accessory drive belt, replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 437 Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped). Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 438 Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Change the automatic transaxle fluid & filter. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 439 Inspect the brake linings, and replace as necessary. Replace the air conditioning filter (if equipped). Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 440 Inspect the exhaust system. Inspect the front suspension, tie rod ends and boot seals, and replace if necessary. Odometer Reading Date Odometer Reading Date Repair Order # Dealer Code Repair Order # Dealer Code Signature Authorized Chrysler Dealer Signature Authorized Chrysler Dealer...
Page 441 MAINTENANCE SCHEDULES 439 † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 443 Reporting Safety Defects ....446 Chrysler LLC Customer Center ..444 In The 50 United States And Washington, D.C.
Page 444 442 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....447 Traction Grades ..... 449 Department Of Transportation Uniform Tire Temperature Grades .
Page 445: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 443 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 446: 444 If You Need Consumer Assistance
Phone: (800) 992-1997 If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center ship. They want to know if you need assistance. P.O. Box 1621...
Page 447: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 445 Customer Assistance For The Hearing Or Speech have any questions about the service contract, call the Impaired (TDD/TTY) manufacturer’s Service Contract National Customer Hot- To assist customers who have hearing difficulties, the line at 1-800-521-9922. manufacturer has installed special TDD (Telecommuni- The manufacturer will not stand behind any service cation Devices for the Deaf) equipment at its customer...
Page 448: Warranty Information (U.s. Vehicles Only)
WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and If NHTSA receives similar complaints, it may open an provisions of Chrysler Motors LLC warranties applicable investigation, and if it finds that a safety defect exists in to this vehicle.
Page 449: In Canada
Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B need in diagnosing/troubleshooting, problem solving, 3V9. maintaining, servicing, and repairing Chrysler LLC vehicles. A complete working knowledge of the ve- hicle, system, and/or components is written in straightforward language with illustrations, diagrams,...
Page 450 Owner’s Manuals These Owner’s Manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler LLC vehicles. Included are starting, operating, emergency and main- tenance procedures as well as specifications, capabili- ties and safety tips.
Page 451: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 449 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 452 450 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 453: Index
INDEX...
Page 454 452 INDEX About Your Brakes ....283,288 Airbag Maintenance ..... . . 58 ABS (Anti-Lock Brake System) .
Page 455 INDEX 453 Automatic Temperature Control (ATC) ..254 Beverage Holder Cooled (Cupholder) ..168 Automatic Transaxle ....270,395 Beverage Holder Heated (Cupholder) .
Page 456 454 INDEX Calibration, Compass ..... 198 Checks, Safety ......73 Capacities, Fluid .
Page 457 INDEX 455 Convertible ......81 Heated/Cooled (Beverage Holder) ..168 Convertible Top .
Page 458 456 INDEX Oil (Engine) ......376 Electronic Speed Control (Cruise Control) ..155 Power Steering .
Page 459 INDEX 457 Exhaust Gas Caution ....74,330 Extender, Seat Belt ......48 Fuel Requirements .
Page 460 458 INDEX Engine Oil ......333 Freeing A Stuck Vehicle ....364 Fuel Requirements .
Page 461 INDEX 459 Fuses ....... . 405 GVWR ....... 337 Garage Door Opener (HomeLink ) .
Page 462 460 INDEX Switch ......143,144 Ignition Key Removal ..... 13 Time Delay .
Page 463 INDEX 461 Jump Starting ......361 Life of Tires ......313 Light Bulbs .
Page 464 462 INDEX Headlight Switch ....143,144 Passing ......148 Headlights .
Page 465 INDEX 463 Low Tire Pressure System ....317 Electric Powered ..... . . 100 Lower Anchors and Tether for CHildren Electric Remote .
Page 466 464 INDEX Oil, Engine ......376,421 Outside Rearview Mirrors ....100 Capacity .
Page 467 INDEX 465 Deck Lid Release ..... . . 36 Radio, Satellite ......243 Door Locks .
Page 468 466 INDEX Replacement Keys ......16 Schedule, Maintenance ....424 Replacement Parts .
Page 469 INDEX 467 Height Adjustment ..... 135 Shoulder Belts ......40 Lumbar Support .
Page 470 468 INDEX Power ......282 Theft System (Security Alarm) ....18 Tilt Column .
Page 471 INDEX 469 Life of Tires ......313 Disabled Vehicle ..... . . 365 Load Capacity .
Page 472 470 INDEX Overdrive ......275 UConnect (Hands-Free Phone) ....102 Selection of Lubricant .
Page 473 INDEX 471 Warning Flasher, Hazard ....352 Windows ......33 Warning Lights (Instrument Cluster Power .
Page 474 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Page 475 Chrysler LLC 81-026-0936 First Edition Printed in U.S.A.

This manual is also suitable for:

2009 sebring convertible

Chrysler Sebring Convertible Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

326 Starting and Operating

Starting and Operating 333

What to Do in Emergencies

Maintaining Your Vehicle

Quick Links

Chapters

Related Manuals for Chrysler Sebring Convertible

Summary of Contents for Chrysler Sebring Convertible