Toshiba H7 Operation Manuals page 224

Commercial Power Switching Frequency Hold
Time, 116
Commercial Power Wait Time, 115
Common Serial (TTL), 15
Communication Baud Rate (logic), 168
Communication Error, 44, 172
Communication Internal, 169
Communication Reference, 170
Communication Reference Adjust, 43
Communication Setting Parameters, 42
Communication Settings, 42
Communications Reference Setpoint #1 (%), 170
Communications Reference Setpoint #2 (%), 171
Communications Speed Setpoint #1 (frequency), 170
Communications Speed Setpoint #2 (frequency), 171
concerns about this publication, 2
Conduit Extender Box, 195
Conduit Plate Information, 188, 193
Configuration and Menu Options, 30
Connecting the ASD, 8
Connection Diagram, 18
Contrast (adjustment), 34
Control Board, 15
Control Terminal Strip, 11
Crane/Hoist Load, 45, 46
Cumulative Run Timer, 40
Cumulative Run Timer Alarm Setting, 158
Current Control Integral Gain, 119
Current Control Proportional Gain, 119
Current/Voltage Specifications, 203
Custom V/f Five-Point Setting #1 Frequency, 80
Custom V/f Five-Point Setting #1 Voltage, 81
Custom V/f Five-Point Setting #2 Frequency, 81
Custom V/f Five-Point Setting #2 Voltage, 81
Custom V/f Five-Point Setting #3 Frequency, 81
Custom V/f Five-Point Setting #3 Voltage, 81
Custom V/f Five-Point Setting #4 Frequency, 82
Custom V/f Five-Point Setting #4 Voltage, 82
Custom V/f Five-Point Setting #5 Frequency, 82
Custom V/f Five-Point Setting #5 Voltage, 82
Customer Support Center, 2
D
Date and time setting, 34
DC Braking, 39
DC Injection Braking Current, 102
DC Injection Braking Start Frequency, 102
DC Injection Braking Time, 102
DCL Selection Table, 208
Dead Time Compensation, 46
Decel #1 Time, 52
Decel #2 Time, 137
H7 Operation Manual
Decel #3 Time, 140
Decel #4 Time, 141
Deceleration Time Adjustment, 162
Default Setting Changes, 26
Default Term. Setting, 11
Direct Access, 34
Direct Access Parameter Information, 48
Direct Access Parameters/Numbers, 48
Direction (of motor rotation), 51
Display Units, 35
Display Units for Voltage and Current, 165
Disposal, 5
Down Key, 23
Drive Capacity, 22
Drive Characteristics, 22
Driving, 129
Driving Torque Limit #1, 129
Driving Torque Limit #2, 129
Driving Torque Limit #3, 130
Driving Torque Limit #4, 130
Drooping, 113
Drooping Control, 41
Dynamic Braking, 39, 110
Dynamic Braking Enable, 110
E
Electronic Gear Setting, 118
Electronic Operator Interface, 23
Electronic Thermal Protection #1, 54, 154
Electronic Thermal Protection #2, 78
Electronic Thermal Protection #3, 79
Electronic Thermal Protection #4, 80
Emergency Off DC Injection Application Time, 155
Emergency Off Mode Settings, 155
Emergency Off Setting, 39
Enclosure Dimensions, 188, 211
Enclosure Dimensions/Weight, 188
Encoder, 210
End Frequency, 101
Enter Key, 23
EOI Bezel Mounting Dimensions, 202
EOI Bezel Plate Dimensions (mounting), 202
EOI Features, 23
EOI Installation Precautions, 200
EOI Operation, 24
EOI Remote Mounting using the ASD-MTG-KIT, 201
EOI Remote Mounting w/o the ASD-MTG-KIT, 201
EOI Setup Options, 34
Escape Key, 23
Extended Terminal Function, 61
Extender Cables, 200
217