Table of Contents
Advertisement
...2 OPERATION
Use the Menu Key
to scroll through
the Menus
Section 2.3, Page 6
Section 3.1, Page 9
VIEW SETPOINTS
OPERATING PAGE
A1: Setpoint
A2: Setpoint
Use the Downscroll
A3: Setpoint
Key to scroll through
the Farmes
A4: Setpoint
within each Page
A5: Setpoint
Section 4.1, Page 17
SENSOR CAL.
Cal. User Code
Section 5.1, Page 19
SECURITY CODE
Section 5.2, Page 20
CONFIG. DISPLAY
Section 5.3, Page 21
CONFIG.SENSORS
Config. Sensor A
A: Cond.Units
A: Cell Constant
A: T.Comp. Range
A: Temp.Comp.
A: Temp. Sensor
A: Temp.Coeff.
A: TDS Factor
A: TDS Units
A: Enable Cals.
Section 5.4, Page 30
CONFIG.ALARMS
Config. Alarm 1
A1: Type
A1: Assign
A1: Failsafe
A1: Action
A1: USP Offset
A1: Setpoint
A1: Hysteresis
A1: Delay
To
CONFIG. OUTPUTS
(see Fig. 2.3B)
4
Use the Sidescroll Key to scroll through the Pages within each Menu
Section 3.2, Page 10 Section 3.3, Page 11
VIEW OUTPUTS
Analog Output 1
Analog Output 2
Analog Output 3
Analog Output 4
Sensor Cal. A
A: Calibration
A: Sensor Slope
A: Sensor Offset
A: Temp. Slope
A: Temp. Offset
A: Reset?
Set Language
Set Temp. Units
English
Temp. Units
Config. Sensor B
B: Cond.Units
B: Cell Constant
B: T.Comp. Range
B: Temp.Comp.
B: Temp. Sensor
B: Temp.Coeff.
B: TDS Factor
B: TDS Units
B: Enable Cals.
Config. Alarm 2
A2: Type
A2: Assign
A2: Failsafe
A2: Action
A2: USP Offset
A2: Setpoint
A2: Hysteresis
A2: Delay
Fig. 2.3A Overall Programming Chart
Section 3.4, Page 12
VIEW HARDWARE
VIEW SOFTWARE
Sensor A Module
AX450/2000 Issue
Sensor B Module
Option Board
Sensor Cal. B
B: Calibration
B: Sensor Slope
B: Sensor Offset
B: Temp. Slope
B: Temp. Offset
B: Reset?
Set Backlight
LED Backlight
Signal Calc
After Cat. Limit
Key
Config. Alarm 3
Config. Alarm 4
A3: Type
A4: Type
A3: Assign
A4: Assign
A3: Failsafe
A4: Failsafe
A3: Action
A4: Action
A3: USP Offset
A4: USP Offset
A3: Setpoint
A4: Setpoint
A3: Hysteresis
A4: Hysteresis
A3: Delay
A4: Delay
Section 3.5, Page 13
Section 3.6, Page 16
VIEW LOGBOOK
VIEW CLOCK
Alarms
Date
Errors
Time
Power
Cals
Available only if the option board is fitted and
analog features enabled – see Section 7.3
Dual input analyzer only
Config. Alarm 5
A5: Type
A5: Assign
A5: Failsafe
A5: Action
A5: USP Offset
A5: Setpoint
A5: Hysteresis
A5: Delay
05:02:04
12:00
Advertisement
Table of Contents
