Table Of Contents - IntesisBox DK-RC-KNX-1i User Manual

®
IntesisBox KNX - Daikin A.C. (SKY & VRV line)
INDEX
1. Presentation .................................................................................................... 6
2. Connection ...................................................................................................... 7
2.1 DK-RC-KNX-1i without DAIKIN Remote Controller ............................................. 7
2.2 DK-RC-KNX-1i with DAIKIN Remote Controller .................................................. 7
3. Configuration and setup .................................................................................... 9
4. ETS Parameters ............................................................................................. 10
4.1 General dialog ............................................................................................ 11
4.1.1 DK-RC-KNX-1i is master in P1/P2 bus ...................................................... 11
4.1.2 Send READs for Control_ objects on bus recovery ..................................... 12
4.1.3 Scene to load on bus recovery / startup ................................................... 12
4.1.4 Disallow control from remote controller .................................................... 12
4.1.5 Enable func "Control_ Lock Control Obj" ................................................... 13
4.1.6 Enable func "Operating Hours Counter" .................................................... 13
4.1.7 Enable object "Error Code [2byte]" .......................................................... 14
4.1.8 Enable object "Error Text Code [14byte]" ................................................. 14
4.2 Mode Configuration dialog ............................................................................ 14
4.2.1 When mode is AUTO Status_ objs report actual operating status ................. 15
4.2.2 Enable use of Heat / Cool bit-type obj ...................................................... 15
4.2.3 Enable PID-Compat. Scaling Mode Objects ............................................... 16
4.2.4 Enable use of + / - object for Mode ......................................................... 16
4.2.5 Enable use of bit-type Mode objects (for control) ...................................... 17
4.2.6 Enable use of bit-type Mode objects (for status)........................................ 17
4.2.7 Enable use of Text object for Mode .......................................................... 18
4.2.8 Enable use of Legacy_ object for Mode .................................................... 18
4.3 Special Modes Configuration dialog ................................................................ 18
4.3.1 Enable use of POWER mode .................................................................... 19
4.3.2 Enable use of ECONOMY mode ................................................................ 20
4.3.3 Enable use of ADDITIONAL HEATING mode .............................................. 21
4.3.4 Enable use of ADDITIONAL COOLING mode .............................................. 21
4.4 Fan Speed Configuration dialog ..................................................................... 23
4.4.1 Available fan speeds in Indoor Unit .......................................................... 23
4.4.2 DPT object type for fanspeed .................................................................. 23
4.4.3 Enable use of +/- object for Fan Speed .................................................... 25
4.4.4 Enable use of bit-type Fan Speed objects (for Control) ............................... 26
4.4.5 Enable use of bit-type Fan Speed objects (for Status) ................................ 26
4.4.6 Enable use of Text object for Fan Speed ................................................... 27
4.4.7 Enable use of Legacy_ obj for Fan Speed ................................................. 27
4.5 Vane Up-Down Configuration dialog ............................................................... 28
4.5.1 Indoor unit has Up-Down Vanes .............................................................. 28
4.5.2 Enable "Control_ Vane U-D Swing" .......................................................... 28
4.5.3 DPT object type for Vane Up-Down .......................................................... 29
4.5.4 Enable use of +/- obj for Vane Up-Down .................................................. 30
4.5.5 Enable use of bit-type Vane U-D objects (for Control) ................................ 31
4.5.6 Enable use of bit-type Vane U-D objects (for Status) ................................. 31
4.5.7 Enable use of Text object for Vane U-D .................................................... 32
4.5.8 Enable use of Legacy_ obj for Vane U-D ................................................... 32
4.6 Temperature Configuration dialog.................................................................. 33
4.6.1 Periodic sending of "Status_ AC Setp" ...................................................... 33
4.6.2 Transmission of "Status_ AC Ret Temp" ................................................... 34
4.6.3 Enable use of +/- obj for Setp Temp ........................................................ 34
4.6.4 Enable limits on Control_ Setpoint obj ..................................................... 35
4.6.5 Ambient temp. ref. is provided from KNX ................................................. 35
4.7 Scene Configuration dialog ........................................................................... 37
© Intesis Software S.L. - All rights reserved
This information is subject to change without notice
®
IntesisBox is a registered trademark of Intesis Software SL
User's manual r1.0 eng
URL http://www.intesis.com
Email info@intesis.com
tel +34 938047134
4 / 66