Siemens siprotec 7SD5 User Manual page 621

Addr. Parameter
1126 RM/RL ParalLine
1127 XM/XL ParalLine
1128 RATIO Par. Comp
1130A PoleOpenCurrent
1131A PoleOpenVoltage
1132A SI Time all Cl.
1134 Line Closure
1135 Reset Trip CMD
1140A I-CTsat. Thres.
1150A SI Time Man.Cl
1151 MAN. CLOSE
1152 Man.Clos. Imp.
1155 3pole coupling
1156A Trip2phFlt
1161 VECTOR GROUP U
1162 VECTOR GROUP I
1163 TRANS STP IS
1201 STATE OF DIFF.
1210 I-DIFF>
1213 I-DIF>SWITCH ON
1217A T-DELAY I-DIFF>
1218 T3I0 1PHAS
1221 Ic-comp.
1224 IcSTAB/IcN
1233 I-DIFF>>
1301 I-TRIP SEND
1302 I-TRIP RECEIVE
1303 T-ITRIP BI
1304 T-ITRIP PROL BI
1501 FCT Distance
1502 Minimum Iph>
1503 3I0> Threshold
7SD5 Manual
C53000-G1176-C169-1
Function C Setting Options
P.System Data 2 0.00 .. 8.00
P.System Data 2 0.00 .. 8.00
P.System Data 2 50 .. 95 %
P.System Data 2 1A 0.05 .. 1.00 A
5A 0.25 .. 5.00 A
P.System Data 2 2 .. 70 V
P.System Data 2 0.01 .. 30.00 sec
P.System Data 2 only with ManCl
I OR U or ManCl
CB OR I or M/C
I or Man.Close
P.System Data 2 CurrentOpenPole
Current AND CB
0.2 .. 50.0 A; ∞
P.System Data 2 1A
1.0 .. 250.0 A; ∞
5A
P.System Data 2 0.01 .. 30.00 sec
P.System Data 2 with Sync-check
w/o Sync-check
NO
P.System Data 2 (Setting options depend
on configuration)
P.System Data 2 with PICKUP
with TRIP
P.System Data 2 3pole
1pole leading Ø
1pole lagging Ø
P.System Data 2 0 .. 11
P.System Data 2 0 .. 11
P.System Data 2 Solid Earthed
Not Earthed
Diff. Prot OFF
ON
Diff. Prot 1A 0.10 .. 20.00 A
5A 0.50 .. 100.00 A
Diff. Prot 1A 0.10 .. 20.00 A
5A 0.50 .. 100.00 A
0.00 .. 60.00 sec; ∞
Diff. Prot
0.00 .. 0.50 sec; ∞
Diff. Prot
Dis. General
Diff. Prot OFF
ON
Diff. Prot 2.0 .. 4.0
0.8 .. 100.0 A; ∞
Diff. Prot 1A
4.0 .. 500.0 A; ∞
5A
Intertrip YES
NO
Intertrip Alarm only
Trip
Intertrip 0.00 .. 30.00 sec
Intertrip 0.00 .. 30.00 sec
Dis. General ON
OFF
Dis. General 1A 0.05 .. 4.00 A
5A 0.25 .. 20.00 A
Dis. General 1A 0.05 .. 4.00 A
5A 0.25 .. 20.00 A
Default Setting
0.00 Mutual Parallel Line comp. ratio
RM/RL
0.00 Mutual Parallel Line comp. ratio
XM/XL
85 % Neutral current RATIO Parallel
Line Comp
0.10 A Pole Open Current Threshold
0.50 A
30 V Pole Open Voltage Threshold
0.10 sec Seal-in Time after ALL closures
I or Man.Close Recognition of Line Closures
with
CurrentOpenPole RESET of Trip Command
20.0 A CT Saturation Threshold
100.0 A
0.30 sec Seal-in Time after MANUAL clo-
sures
NO Manual CLOSE COMMAND
generation
None MANUAL Closure Impulse after
CONTROL
with TRIP 3 pole coupling
3pole Trip type with 2phase faults
0 Vector group numeral for voltage
0 Vector group numeral for current
Solid Earthed Transformer starpoint is
ON State of differential protection
0.30 A I-DIFF>: Pickup value
1.50 A
0.30 A I-DIFF>: Value under switch on
condition
1.50 A
0.00 sec I-DIFF>: Trip time delay
0.04 sec Delay 1ph-faults (comp/isol. star-
point)
OFF Charging current compensation
2.5 Ic Stabilising / Ic Nominal
1.2 A I-DIFF>>: Pickup value
6.0 A
NO State of transmit. the intertrip
command
Trip Reaction if intertrip command is
receiv.
0.02 sec Delay for intertrip via binary input
0.00 sec Prolongation for intertrip via
bin.input
ON Distance protection
0.10 A Phase Current threshold for dist.
meas.
0.50 A
0.10 A 3I0 threshold for neutral current
pickup
0.50 A
A.7 Settings
Comments
621