Warning Message And Troubleshooting; Reserve Job Canceled; Compactflash Full; Form Data Canceled - Epson AcuLaser C9200N Service Manual

EPSON AcuLaser C9200N

1.2.2 Warning Message and Troubleshooting

Table 1-8. Warning Message and Troubleshooting
Message
An attempt has been made to
register a new Re-Print Job, Verify
Job, Stored Job or Confidential Job
though the number of registrations
has reached the maximum.
When the user attempted to register
a Re-Print Job or Verify Job, there
was already a Stored Job registered
by same user name or job name.

Reserve Job Canceled

Insufficient capacity of RAM disk.
Or, RAM Disk is set to Off.
Insufficient capacity of
CompactFlash. Or, a
CompactFlash is not installed.
The CompactFlash memory is full

CompactFlash Full

and collated print jobs, form data,
reserve jobs etc. cannot be saved.
The user attempted registration
after reaching the maximum
number.
The USB memory is not installed,

Form Data Canceled

or was removed while registering.
Or, the capacity of the USB
memory is insufficient.
A CompactFlash is not installed.
When downloading PS3 fonts, the

PS3CompactFlash Full

CompactFlash memory is full and
the fonts cannot be saved.
PRODUCT DESCRIPTION
Downloaded from www.Manualslib.com
Explanation Remedy
Delete or print the registered
Re-Print Jobs, Verify Jobs,
Stored Jobs or Confidential
Jobs.
When there is another Stored
Job with the same user name or
job name, either change the job
name and register it or delete
the Stored Job.
Set RAM Disk to Normal or
Maximum if RAM Disk is set
to Off. Increase the RAM Disk
capacity or add more RAM if
RAM Disk is already set to
Normal or Maximum.
Install a CompactFlash if a
CompactFlash is not installed.
Delete unnecessary form data
and Reserve Jobs (Re-Print,
Verify, Stored, and
Confidential).
Delete registered forms. Or,
replace the USB memory.
Check if the USB memory is
installed. Or, replace with
another USB memory with a
larger capacity.
Install a CompactFlash.
Delete previously downloaded
fonts to empty the
CompactFlash memory.
manuals search engine
Table 1-8. Warning Message and Troubleshooting
Message

Can't Print

Check Paper Size

Image Optimum

Not Supported USB
Device xxx
List of Printer Messages
Explanation
Data was disregarded and not
printed due to a problem in the
data. The following are conditions
of this warning.
Bandwidth of the received data
does not match the value
This error occurs when a
determined by the paper size.
printer driver for a different
The received data contains
printer is used. Check the
undefined intermediate codes or
printer and reinstall it if it is an
compression format.
incorrect driver. When printing
Checksums attached to the
from a USB memory, check
intermediate code data using
and reinsert the USB memory.
ESC/Page and ESC/Page-Color
do not match checksums of the
actual data.
Data cannot be read from the
USB memory where print data
is stored.
The paper size for the loaded paper Set the paper of the specified
and specified paper do not match. size.
Printing with PS
This warning occurs when
Printing with PS
memory is insufficient, and the
Add memory.
resolution is reduced.
ESC/Page-Color driver or
Printing with the ESC/Page-
EPSON PCL driver
Color driver or EPSON PCL
Set the priority of the driver
driver
data compression method
This warning occurs when data
to quality.
is compressed with a higher
level of compression.
The USB device (other than a
memory device) or a USB memory
with a hub currently connected to Disconnect the USB memory
the USB port is not supported. A from the USB port, or specify
file check is performed whenever a Clear Warning to clear the
new device is found on the USB warning.
port, and this error occurs at the
point.
Revision D
Remedy
28
Confidential