Epson AcuLaser C9200N Service Manual page 350

EPSON AcuLaser C9200N
MAINTENANCE MENU
Setting item Settings
Maintenance Execute
StatusSht
Clear Error Log Execute
K Toner Admix Execute
C Toner Admix Execute
M Toner Admix Execute
Y Toner Admix Execute
Reset Mainte Counter Execute
Reset LC2 Counter Execute
Reset LC3 Counter Execute
Reset LC4 Counter Execute
Feed Offset MP -3.5 ~ 0.0 ~ 3.5
Scan Offset MP -3.5 ~ 0.0 ~ 3.5
Feed Offset C1 -3.5 ~ 0.0 ~ 3.5
Scan Offset C1 -3.5 ~ 0.0 ~ 3.5
Feed Offset C2 -3.5 ~ 0.0 ~ 3.5
Scan Offset C2 -3.5 ~ 0.0 ~ 3.5
Feed Offset C3 -3.5 ~ 0.0 ~ 3.5
Scan Offset C3 -3.5 ~ 0.0 ~ 3.5
Feed Offset C4 -3.5 ~ 0.0 ~ 3.5
Scan Offset C4 -3.5 ~ 0.0 ~ 3.5
APPENDIX
Downloaded from www.Manualslib.com
Explanation
Prints Maintenance Status Sheet and Error Log
Sheet.
Clears the saved error log to print it on Error Log
Sheet.
Supplies toner to the developing unit from the
toner cartridge forcibly. Execute this setting for
the low density.
Resets the life counter of the maintenance unit.
Execute this setting after replacing the
maintenance unit.
Resets the life counter of the feed roller (C2).
Execute this setting after replacing the feed
roller.
Resets the life counter of the feed roller (C3).
Execute this setting after replacing the feed
roller.
Resets the life counter of the feed roller (C4).
Execute this setting after replacing the feed
roller.
Sets margins for each paper feeder. "Feed"
indicates the margin on the leading edge of the
paper and "Scan" indicates the margin on the left
edge of the paper.
Control Panel Special Operations
manuals search engine
Setting item Settings
ScanOffset DupMP -3.5 ~ 0.0 ~ 3.5
ScanOffset DupC1 -3.5 ~ 0.0 ~ 3.5
ScanOffset DupC2 -3.5 ~ 0.0 ~ 3.5
ScanOffset DupC3 -3.5 ~ 0.0 ~ 3.5
ScanOffset DupC4 -3.5 ~ 0.0 ~ 3.5
C Regist Feed -6 ~ 6
C Regist Scan -6 ~ 6
M Regist Feed -6 ~ 6
M Regist Scan -6 ~ 6
Y Regist Feed -6 ~ 6
Y Regist Scan -6 ~ 6
Loop Fuser -2 ~ 2
Temp1 Normal -10 ~ 10
Temp2 Normal -10 ~ 10
Temp1 Thick -10 ~ 10
Temp2 Thick -10 ~ 10
Temp1 ExtraThk -10 ~ 10
Temp2 ExtraThk -10 ~ 10
Temp1 SuperThk 0 ~ 10
Temp2 SuperThk 0 ~ 10
Temp1 Envelope -10 ~ 10
Temp2 Envelope -10 ~ 10
Temp1 Trnsprnc -10 ~ 10
Temp2 Trnsprnc -10 ~ 10
Transfer 1st NN -5 ~ 5
Revision D
Explanation
Sets the margin on the left edge of the back of a
paper for each Paper Feeder.
Corrects printing positions for each color.
"Feed" indicates the vertical direction, and
"Scan" indicates the horizontal direction.
Corrects the timing that the speed control of
fusing starts to prevent paper wrinkles that may
occur when printing envelopes.
Corrects the heater temperature of the fuser unit.
"1" indicates the heater of the heat roller, and
"2" indicates the heater of the press roller.
Sets the primary transfer bias in NN
environment. As the set value takes one step up/
down, the transfer bias changes per 50 V.
*NN environment = Environment that
temperature and humidity are in standard value.
Confidential
350