Axia element v.2.0 Installation & User Manual page 44

source.
•
BACKWARD FEED DIM GAIN:
unique to Element: Talkback is sent over dimmed
backfeed audio. If you want a hard interruption
(Talkback interrupts Program audio), set it to OFF,
which mutes the audio. But maybe your jocks would
like to just have their program audio dimmed, and
the Talkback come over it so they can still monitor
air while they're being talked to. In this case, input
a value by which the program audio will be dimmed.
Adjustment range is 0dB to -30dB.
•
LOGIC PORT DISABLED/EXCLUSIVE MODE/
Allows you disable GPIO machine
SHARED MODE:
logic to this audio source device or enable it in two
modes. Exclusive mode permits GPIO control asso-
ciated with only a single fader. Shared mode allows
more than one user to send on/off/start signals to a
source via GPIO.
•
GPIO READY ENABLED/DISABLED:
vices such as CD players or tape machines to sig-
nal their state to the operator through the
READY
OFF button LED. If a device is cueing, its OFF lamp
will not be lit. Tying the device's OFF lamp to the
Ready command means that a machine must be cued
and ready before the OFF lamp illuminates.
If , the OFF lamp illuminates only when the
Enabled
fader is OFF and the Ready command is active on
the GPIO. If
Disabled
normally whenever the fader is turned OFF.
•
FEED-TO-SOURCE MODE:
associated with this source, this option determines
what content is fed back from the board.
»
Auto (Pgm-1/Phone)
(minus the source) when this source's fader is
ON, and feeds the Phone bus (minus the source)
when the fader is OFF. The Phone bus is actually
a special variant of PGM4. The Phone bus is pre-
fader and pre-on/off to allow speaker-phone style
operation thru the Operator's mic.
feeds the Phone bus, minus the source.
»
Phone
Phone is a mono-sum, pre-fade and pre-on/off
variation of PGM4
This is a feature
Allows de-
, the OFF lamp illuminates
If there is a backfeed
feeds the Program 1 bus
©2016 Axia Audio- Rev 1.8.1
feeds the Program 1 bus, minus the source.
»
PGM1
feeds the Program 2 bus, minus the source.
»
PGM2
feeds the Program 3 bus, minus the source.
»
PGM3
feeds the Program 4 bus, minus the source.
»
PGM4
feeds the Aux Send A bus, minus
»
AUX SEND A
the source.
feeds the Aux Send B bus, minus
»
AUX SEND B
the source.
feeds the Aux Send C bus, minus
»
AUX SEND C
the source.
feeds the Aux Send D bus, minus
»
AUX SEND D
the source.
About the PHONE, RECORD and PROGRAM
4 buses: Element's PGM-4 mix bus is a spe-
cial multi-purpose bus that does several things
at once to make life easier for the operator.
Sources assigned to PGM-4 are also sent to the
RECORD bus, a special post-fader, pre-on/off
output that can be used to feed recording de-
vices.
At the same time, sources assigned to PGM-4
are mixed and sent to the PHONE bus. PHONE is
an internal bus which does not feed a separate
output; instead, it picks up PGM-4 audio pre-
fader and pre-On/Off and backfeeds it callers
(minus themselves, of course) when the channel
is OFF and AUTO is selected as the Feed To
Source Mode.
Figure 3-5: Mode and Trim Source Profile Settings
Determines whether source will be
•
SIGNAL MODE:
treated as mono or stereo, and how.
feeds incoming L/R signal to left and
»
Stereo
right channels of assigned bus(es).
feeds incoming left channel to both chan-
»
Left
nels of assigned bus(es).