Greetings; Display Temperature; Display Area Icons; Trouble Alert Beeps - Bosch solution 6000 Installation Manual

Greetings

This option allows the keypad to breifly display on the
top line the greeting message when a user turns an area
on or off.
When turning an area All On, Part On or Part 2 On, the
greeting message 'Goodbye' along with their user name
on the second line will be displayed:
Goodbye
Mary Smith
Security System ON
When turning an area off from All On, Part On or Part 2
On, the greeting message will by displayed on the top
line along with their user name on the second line.
The following greeting messages are as follows:
™ Good Morning Greeting = 00:00 to 11:59
™ Good Afternoon Greeting = 12:00 to 17:59
™ Good Evening Greeting = 18:00 to 23:59
Good Morning
Mary Smith
Security System OFF

Display Temperature

This option allows the keypad to display the reading of
the keypad temperature when a keypad idle screen has
been programmed. Each keypad can display its own
temperature.

Display Area Icons

TThis option allows the keypad to display the area icons
1 to 8. This allows the users to determine which areas are
turned All On or Part On from a single keypad without
the need to either move the keypad display to view each
area or walk to each area keypad.
Security System
DISARMED
Thu,Jan,05 11:22 am

Trouble Alert Beeps

This option allows the LAN device (keypad, proximity
reader or fingerprint reader) to sound a trouble tone
when the system has detected a trouble condition.

Entry Exit Warning

This option allows the LAN device (keypad, proximity
reader or fingerprint reader) to sound the entry warning
tone or sound the exit warning tone when a user turns
an area All On.
Bosch Security Systems 07/14 BLCC610I

Part Exit Warning

This option allows the LAN device (keypad, proximity
reader or fingerprint reader) to sound the exit warning
tone when a user turns the area Part On or Part 2 On.
If this option is not programmed, the keypad will only
sound a single beep at the end of the part exit time.

Chime Tone

This option allows the LAN device (keypad, proximity
reader or fingerprint reader) to sound the chime tone
when a a zone set to be monitored when chime mode is
turned on is faulted. If this option is not programmed,
the LAN device will not sound the chime tone when a
chime zone is faulted.
Devices > Keypads & Readers >

Emergency Keys

1
2
3
4
5
6
7
8
The above options can be configured independantly for
each keypad fitted to the system.
1) Press [MENU] + [6] + [1] + [6] and use the up and
2) Use the up and down arrow keys to highlight the
3) Repeat Step 2 until all options are programmed as
22ºC

Audible Keypad Fire

Setting this option allows the panel to sound an audible
alarm when a Keypad Fire Emergency Alarm has been
triggered via the keypad. To initiate a fire emergency via
the keypad, press and hold the [4] + [6] keys or the [←] +
[→] keys down for two seconds. Enter a valid user PIN to
reset the alarm condition.

Report Keypad Fire

Setting this option allows the panel to send a Fire report
to the base station when a Keypad Fire Emergency Alarm
Solution 6000
Installation Manual

Audible Keypad Fire
Report Keypad Fire
Audible Keypad Medical
Report Keypad Medical
Audible Keypad Panic
Report Keypad Panic
Reserved
Reserved
down arrows to highlight the keypad in the list
then press [OK].
 Audible Keypad Fire
 Report Keypad Fire
 Audible Keypad Medical
Press  OK ON OFF MENU
option then press the [ON] key to enable or the
[OFF] key to disable.
required, then press [OK] to save and exit or press
[MENU] to exit without saving.
Device Programming

 MENU 6-1-6
Y
Y
Y
Y
Y
Y
N
N
10-7