Vectorrx, Vrx32-433 And Vectorrx-8 Receiver; Identification Of Parts; Choosing A Mounting Location - Bentel Security KYO 320 Installation Manual

2. Plug the Printer interface into the connector 15 on
the Control panel PCB then, using the screws, se -
cure it in place.
3. Connect the Printer lead to the connector 119 on
the Printer Interface.
VectorRX, VRX32-433 and VectorRX-8
Receiver
The VectorRX, VRX32-433 Receiver (accessory item) will
allow your system to manage up to 32 Wireless detectors
(PIRs, Magnetic Contacts, Smoke detectors), and up to 16
Wireless keys (KeyFobs). VectorRX-8 Receiver man -
ages up to 8 Wireless detectors (PIRs, Magnetic Con -
tacts, Smoke detectors), and up to 8 Wireless keys
(KeyFobs). Please read this section to get an overall
view of the steps involved in installing the VectorRX Re -
ceiver.
The term "Receiver or VectorRX Receiver" has been
used in the parts where the functions and operating
modes are common to all Receivers. However, in parts
where the functions and operating modes differ, the re -
spective Receiver has been specified.
n Identification of Parts
The following Table describes the components of the
Receiver (see Figure 62-64-65). The numbers in bold -
face in this section, refer to the descriptions in the Table
and Figure.
1 2 3 4
18 wire cable + shield: the shield must be soldered to the metal casing of both connectors
1 2 3 4
Table 12 Wiring diagram of the cable between the parallel printer and the Printer Interface
118
Figure 60 Printer Interface components
92
Interface connector: DB25 connector, male
5 6 7 8 9
5 6 7 8 9
Printer side: Centronics connector, 36 pin, male
119
No.
120 Spring catch slots (2)
121 Anchor screw locations (3 x ø 4.6 mm)
122 Antennas (2)
123 Microprocessors (2)
124 Seize microswitch
125 Tamper button
126 Screws (2)
127 Wire entry (10 x 6.4 mm)
128 Spring Catch
129 Terminal board
129a PCB clip
n Choosing a Mounting Location
+
Mount the Receiver and Wireless Devices after the
placement tests.
Choose a place that is:
Ø Dry
Ø Central to the proposed placement of all Wireless
Devices
Ø As close to the ceiling as possible
Ø Far from sources of interference such as: electrical
noise (computers, televisions, electric motors in ap-
pliances, and heating and air-conditioning units),
and large metal objects (heating ducts and plumb-
ing) which may shield the antennas.
Ensure that no electrical wires run over the Receiver
antennas. When mounting in a basement, place the
module as high and as close to the underside of the first
floor as possible. The range of the Receiver will be re-
duced if the unit is mounted below ground level.
10 11 12 13 14
10 11 12 13 14
Printer side:
36 18
Centronics connector, male:
35 17
pins from 15 to 17 and 19 through 30
must be connected together
34 16
and to pin 19 of the DB25 connector
33 15
32 14
31 13
30 12
29 11
28 10
27 9
26 8
25 7
24 6
23 5
22 4
21 3
20 2
19 1
Figure 61 Wiring diagram of parallel printer cable
DESCRIPTION
15 16 17
32 31 36 15÷17/19÷30
Interface side:
connector
18 wire shielded cable
(max. length 10 m) :
the shield must be soldered
to the metallic casing
of both connectors
19
DB25
male
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1