Compound Messages; Teleservice - Bentel Security KYO 320 Installation Manual

Description This editable field is for the Message label
(maximum 16 characters).
Quality This field will allow you to select the sound qual -
ity, as follows: click the required cell; click again to high -
light the programming field; click the arrow to open the
drop-down menu.
(for 63 and 64 messages only). For all other messages
during Recording it is possible to set the Time and the
Quality.
Time Enter the Message length (in seconds) (for 63
and 64 messages only).
With quality Select the Voice Message quality.
Leftover Time This field will show the residual time
which can be added to other Voice Messages.
The residual time depends on the selected quality.
n Compound Messages
The Control panel Dialler can manage Compound Mes -
sages. This type of Message takes up less time than a
regular Message. Therefore, if you must record several
messages with parts in common, such as an Address,
the Compound Message will allow you to save mes -
sage time.
For example, instead of recording:
Ø Message 1 (regular Message taking 5 seconds)
<<Burglar Alarm, Stef's Café, King St., St. Helier>>
Ø Message 2 (regular Message taking 5 seconds)
<<Fire Alarm, Stef's Café, King St., St. Helier>>
Ø Message 3 (regular Message taking 5 seconds)
<<Duress Alarm, Stef's Café, King St., St. Helier>>,
you can record:
Ø Message 1 (1 second) <<Alarm>>
Ø Message 2 (1 second) <<Burglar>>
Ø Message 3 (1 second) <<Fire>>
Ø Message 4 (1 second) <<Duress>>
Ø Message 5 (4 seconds) <<Stef's Café, King St., St.
Helier>>
and combine the messages to obtain the
same contents, as follows:
Ø Message 1 = Messages 2 + 1 + 5
Ø Message 2 = Messages 3 + 1 + 5
Ø Message 3 = Messages 4 + 1 + 5
The three regular Messages take 15 seconds
while the three Compound Messages take
only 8 seconds, thus saving 7 seconds.

Teleservice

The B-Mod or B-Mod/RX modem and the
KYO320 application from the Security Suite will
allow you to provide the Teleservice function
(access to the system via telephone).
Teleservice calls can be made by the installer
(Teleservice calls to the Control panel require
User authorization), or by the User (if the
Control panel has been setup to perform the
KYO320
automatic Test Event).
When the Control Panel generates a Teleservice call
(manually, by User request, or automatically via the
Callback or Enable Test Call options (these options
must be Enabled), it will dial the programmed numbers
(refer to Enable and Telephone number to call) until a
call is successful, or until the programmed call At -
tempts cycle ends.
The layout of Teleservice page as follows.
Double call This option will allow the Control Panel to
share the telephone line with another answering device
(answering machine, fax, etc.). Under normal circum -
stances, the device which allows the least number of
rings will answer any incoming calls. However, if this
option is Enabled, the Control panel will override the
other answering device when it recognizes the Double
Call sequence.
Double Call sequence: the caller must allow no more
than 2 rings, then hang up and callback within 60 sec -
onds. The Control panel will answer on the first ring of
the second call.
+
The other answering device must be programmed
to answer after 3 or more rings.
The B-Mod modem manages the Double call option au-
tomatically.
To access the system over the phone: ring twice and hang
up, then call the Control Panel again within 60 seconds.
Callback If this option is Enabled, the Control panel
will call the Enabled telephone numbers (refer to En-
able and Telephone number to call on the
Teleservice page). In this way, ONLY authorized per-
sons can access the Teleservice function.
Enable This check box will allow you to Enable the
Teleservice number.
Figure 39 Voice Messages page
PROGRAMMING 53