Telim; Scheduler - Arming 71 Contact Id; Mounting The B-Net Module; Technical Specifications - Bentel Security KYO 320 Installation Manual

No. DESCRIPTION
130 Backplate screw locations (4)
131 Connector for the Control panel link.
132 Microprocessors (2)
133 LAN link
134 Cable entry
135 Terminal board
136 Anchor screw holes (4)
137 Earth Wire entry (see Fig.64)
138 Tamper microswitch (Accessory item)
n Mounting the B-NET Module
The B-NET Module should be mounted on a flat wall di -
rectly below the Control panel. Do not mount the
B-NET Module on an uneven surface as this may affect
proper closure of the box. Work through the following
instructions carefully (see Figure 63).
1. Remove the screws 130 and frontplate.
2. Drill the holes 136 for the B-NET Module anchor
screws.
3. Pull the connection wires through the cable entry
134 then attach the backbox to the wall.
4. Complete the connections — DO NOT connect the
Mains until all other wiring has been completed.
5. Using the B-NET link (inside the package), connect
the B-NET Module (via connector 131) to the serial
port on the mother board, then connect the B-NET
Module (via connector 133) to the LAN.
+
If required, connect the Tamper microswitch to the
Control panel tamper line.
INPUT
EXPANDER
BUS BPI
BUS BPI
POWER SUPPLY
LAN NET
Figure 68 Example of a B-NET configuration
KYO320
KEYPAD
OUTPUT
EXPANDER
A
K
K A
READER and DIGITAL KEY
PICVUE 160206QGL01 WINTEK WM-C1602N-2GLYc
1 2 3 C
abc def
A B
4 5 6
D
ghi jkl mno
7 8 9 ESC
pqrs tuv w xyz
ON 0 OFF
#
Des. n.
Inserimento Aree Arming Partitions Inserite Aree Armed Partitions
1 2 Inserimento A, B, C o D Arming Type A, B, C or D PIN O Guasto Allarme Alarm Warning
3 4 Disinserimento Aree PIN A B C D o Sabotaggio Messaggio Panel Message
or o Centrale Tamper
5 6 Disarming Partitions Reset Memorie PIN Sabotaggio Sabotaggio Periferica Tamper Peripheral Tamper
7 EE
Reset Alarms Blocco AllarmeQ PIN Scomparsa Falsa Periferica Chiave Peri heral False Ke /Card Missing p y
8 Stop AlarmsQ PIN EDE Teleassist. Teleservice
Abilitata Enabled
Cancella Telefonate Clear Calls PIN Telefonata Rispondit. Call in Answer
ECE in corso Abilitato progress Phone ON
http:\\www.bentelsecurity.com
DETECTORS
KYO320 CONTROL PANEL
B- NE T B-NET MODULE
® ®
n Technical Specifications
The following table contains the technical specifications
of the B-NET Module.
Voltage
Current draw
Dimensions (W x H x D)
Weight

Reset default

To reset the factory default programming:
1. Remove all power from the Control panel (Mains
and battery).
2. Remove the jumper 21 (M).
3. Wait at least 20 seconds.
4. Replace the jumper 21 (M).
5. Restore power to the Control panel (refer to "Con-
necting the Power Supply" under "INSTALLING THE
KYO320").
!
Jumper 21 (M) must be disconnected for at
least 20 seconds in order to ensure full reset of
the factory default programming, and to avoid
problems that may occur when the power sup-
ply is restored.
Installer code locked If the Lock Installer code op-
tion is enabled, the Installer PIN will not be able to reset
to factory default (refer to Lock Installer code in the Op-
tions section).

Reporting Formats

This paragraph describes the structures of the main
reporting formats supported by the system.
n TELIM
The TELIM protocol transmits as follows:
Ø User Code (4 digits — 0 through 9);
Ø Event Code: 41 in the event of Alarm or Tamper on
the first 16 zones of the Control panel, 0 in all other
cases;
Ø 2 byte (16 bit) representing the status of the first 16
zones — 0 Standby; 1 = Alarm or Tamper.
SERVER
n Contact ID
Contact ID transmits as follows:
Ø User Code (4 hexadecimal digits — 0 through F );
Ø Qualifier: 1 = new event or Disarming operation; 3
event restore event or Arming operation
Ø Class Code (CL. column): identifies the type of
event (Alarm, Trouble, Fire, etc.);
Ø Event Code (CODE column): identifies the event
(Event Codes can be changed, refer to "Actions" un-
APPENDIX
13.8 V_
250 mA
150 x 339 x 108 mm
1475 g
95