Indicator Operations; Toggle Gross/Net Mode; Toggle Units; Zero Scale - Rice Lake IQ plus 710 Installation Manual

1.3

Indicator Operations

Basic IQ plus 710 operations are summarized below:
1.3.1

Toggle Gross/Net Mode

Press the key to switch the display mode
GROSS/NET
from gross to net, or from net to gross. If a tare value
has been entered or acquired, the net value is the gross
weight minus the tare. If no tare has been entered or
acquired, the display remains in gross mode.
Gross mode is indicated by the word
Brutto
in OIML mode) on the secondary display; net
mode is indicated by the word

Discontinued Product

1.3.2

Toggle Units

Press the key to switch between primary and
UNITS
secondary units. The units identifier is shown to the
right of the primary display. Troy ounces and troy
pounds are indicated by the word
secondary display.
1.3.3

Zero Scale

1. In gross mode, remove all weight from the
scale and wait for the standstill annunciator
( ).
2. Press the
ZERO
( ) annunciator lights to indicate the
scale is zeroed.
1.3.4

Acquire Tare

1. Place container on scale and wait for the
standstill annunciator (
2. Press the key to acquire the tare weight
TARE
of the container.
3. Display shifts to net weight and shows the
Net
word on the secondary display.
To display the current tare value, press the
key.
TARE
1.3.5

Remove Stored Tare Value

1. Remove all weight from the scale and wait for
the standstill annunciator (
2. Press the key (or, in OIML mode, the
TARE
key). Display shifts to gross weight and
ZERO
shows the word
display.
1.3.6

Print Ticket

1. Wait for the standstill annunciator (
2. Press the
PRINT
port.
Gross
Net
.
troy
on the
key. The center of zero
).
DISPLAY
).
Gross
on the secondary
key to send data to the serial
1.3.7

Display or Change Time and Date

To display the date, press the
press
TIME/DATE
To set the date, press the
numeric keypad to enter the date, then press the
key. The date must be entered in the date
ENTER
format configured for the indicator: MMDDYY,
DDMMYY, or YYMMDD.
To set the time, press the
(or
the numeric keypad to enter the time in 24-hour
format, then press the
1.3.8

Display or Change Setpoint Value

To display a setpoint value, use the numeric keypad to
enter the setpoint number, then press the
key. Or, you can display a setpoint value by pressing
the key a number of times equal to the
SETPOINT
setpoint number. For example, to display the value of
setpoint 4, press the
To change the setpoint value, display the current
value, then use the numeric keypad to enter the new
value and press the
NOTE: Some indicator configurations may not allow setpoint
values to be changed through the front panel or may require a
password to display or change the setpoint value.
1.3.9

Turn Setpoint On or Off

To turn a setpoint off at the front panel, use the
numeric keypad to enter the setpoint number, then
press the
SETPOINT
number of times equal to the setpoint number). With
the correct setpoint displayed, press
setpoint off.
To re-enable a setpoint on that has been turned off at
the front panel, press the
correct setpoint is displayed, then press
the setpoint back on.
NOTE: Some indicator configurations may not allow setpoints
to be turned off through the front panel or may require a
password to turn the setpoint on and off.
1.3.10

Display or Clear Accumulator

If the accumulator function is enabled, the current net
weight is added to the accumulator each time the
indicator performs a print operation.
• To display the current accumulator value,
press the
).
• To clear the accumulator, press
show the current value, then press the
key twice to reset the accumulator.
TIME/DATE
a second time to display the time.
key once. Use the
TIME/DATE
key twice. Use
TIME/DATE
key.
ENTER
key four times.
SETPOINT
key.
ENTER
key (or, press the
SETPOINT
CLEAR
key until the
SETPOINT
ENTER
key.
ACCUM
Introduction
key once;
SETPOINT
key a
to turn the
to turn
to
ACCUM
CLEAR
3