Panasonic DP-C321 Service Handbook page 182

3-108
116-200 Main PWBA IC Failure
[Detection Conditions] An error was detected in the IC in
the ESS PWB.
[Actions] Replace the ESS PWB (PL13.1).
116-201 HDD Failure
[Detection Conditions]
The HDD was not booted due to a HDD error detected
on booting
[Actions]
Turn the power On/Off and perform the following if
the problem persists.
(1) Run the HDD Diag (DC355).
(2) Replace the HDD.(PL13.1)
(3) ESS PWB (PL13.1)
116-206 Timer Failure
[Detection Conditions] A timer error was detected.
[Actions] Replace the ESS PWB (PL13.1).
116-207 Ethernet Board Failure
[Detection Conditions] A timer error was detected in the
Ethernet board.
[Actions] This code is not supposed to occur.
116-209 ESS Font ROM DIMM #1 Check Failure
[Detection Conditions]
A failure was detected when the ESS FONT ROM
DIMM #1 was checked.
[Actions]
Pull out and insert the ESS FONT ROM DIMM #1.
If the trouble persists, replace the ESS FONT ROM
DIMM #1.
116-310 ESS Font ROM DIMM #2 Check Failure
[Detection Conditions]
A failure was detected when the ESS FONT ROM
DIMM #2 was checked.
[Actions]
Pull out and insert the ESS FONT ROM DIMM #2.
If the trouble persists, replace the ESS FONT ROM
DIMM #2.
116-311 ESS Font ROM DIMM #3 Check Failure
[Detection Conditions]
A failure was detected when the ESS FONT ROM
DIMM #3 was checked.
[Actions]
Pull out and insert the ESS FONT ROM DIMM #3.
If the trouble persists, replace the ESS FONT ROM
DIMM #3.
116-314 Ethernet Address Failure
[Detection Conditions] A Ethernet error was detected.
[Actions]
Turn the power On/Off and perform the following if
the problem persists.
Replace the ESS PWB (PL13.1).
116-315 ESS RAM DIMM #1 W/R Check Failure
[Detection Conditions]
A failure was detected during W/R of the ESS RAM
DIMM #1.
[Actions]
Pull out and insert the ESS RAM DIMM #1.
If the trouble persists, replace the ESS RAM DIMM
#1.
116-316 ESS RAM DIMM #2 W/R Check Failure
[Detection Conditions]
A failure was detected during W/R of the ESS RAM
DIMM #2.
[Actions]
Pull out and insert the ESS RAM DIMM #2.
If the trouble persists, replace the ESS RAM DIMM
#2.
Chapter 3 Troubleshooting
116-317 Standard ROM DIMM Check Failure
[Detection Conditions]
An error was detected when the standard ROM DIMM
was checked.
[Actions]
Pull out and insert the standard ROM DIMM.
If the trouble persists, replace the standard ROM
DIMM.
116-318 Option ROM DIMM Check Failure
[Detection Conditions]
An error was detected when the optional ROM DIMM
was checked.
[Actions]
Pull out and insert the optional ROM DIMM.
If the trouble persists, replace the optional ROM
DIMM.
116-319 Serial Failure
[Detection Conditions]
There is no serial port at the serial board initialization
failure.
[Actions] This code is not supposed to occur.
116-320 STREAMZ Soft Failure
[Detection Conditions]
Fatal error of the STREAMZ
Due to an error during the software processing, the
subsequent processes cannot be performed.
[Actions]
Turn the power On/Off and perform the following if
the problem persists.
(1) Perform re-installation of the ESS software.
(2) Replace the ESS PWB (PL13.1).