Sony HDW-750 Maintenance Manual page 185

SP FUNC Display (Setting the special functions)
O
? 02 SP FUNC
WIDE AWB
COMP OUT ENABLE :
VF SELECT HD/SD :
CHARA 4:3 MODE
SD VF 4:3 MODE
INDICATOR <:>
GAIN DISP MODE
SHT ANGLE MODE
Item Setting
WIDE AWB OFF/ON
COMP OUT ENABLE OFF/ON
VF SELECT HD/SD AUTO/HD/SD
CHARA 4 : 3 MODE OFF/ON
SD VF 4 : 3 MODE OFF/ON
INDICATOR < : > OFF/SCENE/REFER/
LENS/FACT/TEMP/
SVC/ABS/NOALL/STD/
NOALP/NOINI/INIT
*1
GAIN DISP MODE dB/ISO
SHT ANGLE MODE *1 OFF/ON
*1 : This item is displayed only when the unit of which the ROM version of the AT board is 1.70 and higher. You can check the AT
version by the ROM VERSION display in the DIAGNOSIS menu.
HDW-750/750CE V1
: ON
OFF
AUTO
: OFF
: OFF
: OFF
: dB
: OFF
Function
Sets whether to use an attenuator
(R-ch : +6 dB, B-ch : _6 dB) during white balance
automatic adjustment or not to use.
Sets this menu item to ON when the component signal
unit is connected.
Select AUTO for automatic identification of HD/SD.
Select the HD, SD positions for the fixed signals.
Turns ON/OFF the function that adjusts the width of
character into the cut-out width of the 4 : 3 aspect ratio.
Turns ON/OFF the function that output the 4 : 3 aspect
picture during SD VF.
Change the " : " of the each display' s item to" @ ".
(Example) When the SCENE is selected.
INDICATOR < : >
the target item (GAMMA) is displayed on screen as
GAMMA @
OFF :
SCENE : Indicates the items that can be saved in the SCENE file.
REFER : Indicates the items that can be saved in the
LENS :
FACT :
TEMP:
SVC :
ABS :
NOALL : Indicates the items that can't be saved when ALL
STD :
NOALP : Indicates the items that can't be preset when the
NOINI :
INIT :
Refer to Section " 4-10.Setup Menu List" for the each target item.
Turns ON/OFF the function that sets the GAIN value in the
ISO indication.
ISO : ISO indication
dB : Decibel (dB) indication
n
Correspondence between the ISO indication and decibel (dB)
indication is shown below.
Values in parenthesis ( ) indicates the decibel (dB) indication.
440 (_3) /630 (0) /880 (3) /1300 (6) /1800 (9) /2500 (12) /
5000 (18) /10000 (24)/20000 (30) /40000 (36) /80000 (42)
Turns ON/OFF the Step Shutter (such as 1/500) is indicated in
units of angle.
: SCENE
ON
" @ " is not displayed at all items.
REFERENCE file.
Indicates the items that can be saved in the LENS file.
Indicates the items that the factory set value
can be saved in the EEPROM.
The items that do not have the 1-to-1 storage
area with the menu, in the the non-volatile memory.
Indicates the items that can be operated only
by the SERVICE mode.
Absolute value (not the relative value with
respect to the lower layer) .
FILE SAVE and STORE ALL PRESET are executed.
Indicates the items that are returned to the standard
setup (PRESET value).
ALL PRESET is executed.
Indicates the items that doesn't return to the default
setting when the unit was shipped from the factory
at power-on.
Indicates the items that return to the default setting
when the unit was shipped from the factory at
power-on.
4-9. SERVICE Menu
4-63