Checking And Lubricating The Cables; Checking The Throttle Grip Operation - Yamaha FJR13AG Service Manual

▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
3. Check:
• Meter display for the rear brake light switch
"ON" → Adjust the brake light switch or check
the brake pedal operation.
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Connect the Yamaha diagnostic tool.
Use the diagnostic code number "82".
Refer to "SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE (ECU)" on
page 9-5.
b. Check the meter display for the rear brake
light switch.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
EAS30660
CHECKING AND LUBRICATING THE
CABLES
The following procedure applies to all of the in-
ner and outer cables.
EWA13270
WARNING
Damaged outer cable may cause the cable to
corrode and interfere with its movement. Re-
place damaged outer cable and inner cables
as soon as possible.
1. Check:
• Outer cable
Damage → Replace.
2. Check:
• Cable operation
Rough movement → Lubricate.
Recommended lubricant
Engine oil or a suitable cable lu-
bricant
TIP
Hold the cable end upright and pour a few drops
of lubricant into the cable sheath or use a suit-
able lubricating device.
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲▲▲
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼▼▼
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲▲▲
3-32
PERIODIC MAINTENANCE
EAS30861
CHECKING THE THROTTLE GRIP
OPERATION
1. Check:
• Throttle cables
Damage/deterioration → Replace.
• Throttle cable installation
Incorrect → Reinstall the throttle cables.
Refer to "HANDLEBARS" on page 4-87.
2. Check:
• Throttle grip movement
Rough movement → Lubricate or replace the
defective part(s).
Recommended lubricant
Suitable cable lubricant
TIP
With the engine stopped, turn the throttle grip
slowly and release it. Make sure that the throttle
grip turns smoothly and returns properly when
released.
Repeat this check with the handlebar turned all
the way to the left and right.
3. Check:
• Throttle grip free play "a"
Out of specification → Adjust.
Throttle grip free play
1.0–3.0 mm (0.04–0.12 in)
4. Adjust:
• Throttle grip free play
TIP
Prior to adjusting the throttle grip free play, throt-
tle body synchronization should be adjusted
properly.
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Slide back the rubber covers "1".
b. Loosen the locknut "2".
c. Turn the adjusting nut "3" in direction "a" or "b"
until the specified throttle grip free play is ob-
tained.
a
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼▼▼