V/F Control With Pg - YASKAWA VARISPEED-616G5 Instruction Manual

Advanced Operation

7.4 V/f Control with PG

Group
b Application b Application
C Tuning C Tuning
d Reference d Reference
7
E Motor E Motor
F Options F Options
H T H Terminal i l
The functions that can be used with V/f control with PG are listed in Table 7.4. Details on functions that are
specific to V/f control with PG feedback (i.e. those marked with a L) are provided in the following table.
Table
7.4 V/f Control with PG
Function
b1 Sequence
b2 DC Injection Braking
b3 Speed Search
b4 Delay Timers
b5 PID Control
b6 Dwell Functions
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Compensation
C4 Torque Compensation
C5 Speed Controls
C6 Carrier Frequency
C7 Hunting Prevention
C8 Factory Tuning
d1 Preset Reference
d2 Reference Limits
d3 Prohibited Frequencies
Reference frequency hold
d4
function
d5 Torque Control
E1 V/f Pattern
E2 Motor Setup
E3 Motor 2 Control Methods
E4 Motor 2 V/f Characteristics
E5 Motor 2 Motor Constants
PG Speed Control Card
F1
Settings
F2 Analog Reference Card AI
F3 Digital Reference Card DI
F4 Analog Monitor Card AO
F5 Digital Output Card DO
F6 Digital Output Card DO
F7 Pulse Monitor Card PO
SI-F/SI-G Transmission
F8
Card
Transmission Card other
F9
than SI-K2, SI-F/G
H1 Multi-function Inputs
H2 Multi-function Outputs
H3 Analog Inputs
Multi-function Analog Out-
H4
puts
MEMOBUS Communica-
H5
tions
Comments
Settings such as the reference input method
DC injection braking function settings
Speed search function settings
Timer function settings
PID control settings
Acceleration/deceleration time dwell function settings
Not used. (Can't be set.)
Multi-function input: Sets energy-saving control by energy saving
L
reference.
Not used. (Can't be set.)
Acceleration/deceleration time settings
S-curve characteristics for accel/decel times
Slip compensation function settings
Torque compensation function settings
Speed control adjustment
Carrier frequency settings
L Hunting prevention settings
Not used. (Can't be set.)
Frequency reference settings (when using Operator)
Frequency upper and lower limit settings
Prohibited frequency settings
Up/Down, Accel/Decel stop hold frequency setting
Not used. (Can't be set.)
Motor constant settings Motor constant settings
L L
(Motor constants are set manually.)
Control method settings for motor 2.
V/f characteristics settings for motor 2.
Motor constant settings for motor 2.
Constant settings for a PG Speed Control Card
User constant settings for an Analog Reference Card
User constant settings for a Digital Reference Card
User constant settings for an Analog Monitor Card
User constant settings for a Digital Output Card
User constant settings for a Digital Output Card
User constant settings for a Pulse Monitor Card
User constant settings for a Transmission Card
User constant settings for a Transmission Card
Function selection for multi-function inputs
Function selection for multi-function outputs
Function selection for analog inputs
Function selection for analog outputs
MEMOBUS communications settings
7 - 36
Control Meth-
od
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
× × ×
f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
×
f f f
× f × f
f f f f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
f f f f
× ×
f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f
f f f
f f f f