V/F Control Without Pg; Normal V/F Control Functions - YASKAWA VARISPEED-616G5 Instruction Manual

7.2 V/f Control without PG

The functions that can be used with vector control without PG are listed in Table 7.2. Details on functions that
are specific to vector control without PG (i.e. those marked with a
Table 7.2
Group
b1 Sequence
b2 DC Injection Braking
b3 Speed Search
b4 Delay Timers
b Application b Application b5 PID Control
b6 Dwell Functions
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Compensation
C4 Torque Compensation
C Tuning C Tuning
C5 Speed Controls
C6 Carrier Frequency
C7 Hunting Prevention
C8 Factory Tuning
d1 Preset Reference
d2 Reference Limits
d3 Jump Frequencies
d Reference d Reference
Reference Frequence Hold
d4
Function
d5 Torque Control
E1 V/f Pattern
E2 Motor Setup
E Motor E Motor E3 Motor 2 Control Methods
E4 Motor 2 V/f Characteristics
E5 Motor 2 Motor Constants
PG speed control card set-
F1
tings
F2 Analog Reference Card AI
F3 Digital Reference Card DI
F4 Analog Monitor Card AO
F5 Digital Output Card DO
F Options F Options
F6 Digital Output Card DO
F7 Pulse Monitor Card PO
SI-F/SI-G Transmission
F8
Card
Transmission Cards other
F9
than SI-K2 and SI-F/G
H1 Multi-function Inputs
H2 Multi-function Outputs
H3 Analog Inputs
H T H Terminal i l
Multi-function Analog Out-
H4
puts
MEMOBUS Communica-
H5
tions

Normal V/f Control Functions

Function
Settings such as the reference input method
DC injection braking function settings
Speed search function settings
Timer function settings
PID control settings
Acceleration/deceleration time dwell function settings
Not used. (Can't be set.)
L Multi-function input: Energy-saving control settings
Not used. (Can't be set.)
Acceleration/deceleration time settings
S-curve characteristics for accel/decel times
Slip compensation function settings
Torque compensation function settings
Not used. (Can't be set.)
Carrier frequency settings
L Hunting prevention function settings
Not used. (Can't be set.)
Frequency reference settings (when using Operator)
Frequency upper and lower limit settings
Prohibited frequency settings
Up/Down, Accel/Decel stop hold frequency setting
Not used. (Can't be set.)
Motor constant settings Motor constant settings
L L
(Motor constants set manually.)
Control method settings for motor 2.
V/f characteristics settings for motor 2.
Motor constant settings for motor 2.
Not used. (Can't be set.)
User constant settings for an Analog Reference Card
User constant settings for a Digital Reference Card
User constant settings for an Analog Monitor Card
User constant settings for a Digital Output Card
User constant settings for a Digital Output Card
User constant settings for a Pulse Monitor Card
User constant settings for a Transmission Card
User constant settings for a Transmission Card
Function selection for multi-function inputs
Function selection for multi-function outputs
Function selection for analog inputs
Function selection for analog outputs
MEMOBUS communications settings
7 - 11
7.2 V/f Control without PG
) are provided in the following table.
L
Comments
Control Meth-
od
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
× × ×
f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
×
f f f
× ×
f f
f f f f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
× × ×
f
f f f f
7
f f f f
f f f f
f f f f
f f f f
× ×
f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
− − − −