Analog Inputs: H3 - YASKAWA VARISPEED-616G5 Instruction Manual

Analog Inputs: H3

J
Name
C Constant
Number
Display
Signal level selection
(terminal 13)
H3-01 H3 01
Term 13 Signal
Gain (terminal 13)
H3 02 H3-02
Terminal 13 Gain
Bias (terminal 13)
H3-03 H3 03
Terminal 13 Bias
Signal level selection
(terminal 16)
H3-04 H3 04
Term 16 Signal
Multi-function analog
input (terminal 16)
H3 05 H3-05
Terminal 16 Sel
Gain (terminal 16)
H3-06 H3 06
Terminal 16 Gain
Bias (terminal 16)
H3-07 H3 07
Terminal 16 Bias
Signal level selection
(terminal 14)
H3-08 H3 08
Term 14 Sel
Multi-function analog
input (terminal 14)
H3-09 H3 09
Terminal 14 Sel
Gain (terminal 14)
H3 10 H3-10
Terminal 14 Gain
Bias (terminal 14)
H3-11 H3 11
Terminal 14 Bias
Analog input filter
time constant
H3 12 H3-12
Filter Avg Time
Description
0: 0 to + 10V [11-bit + polarity
(positive/negative) input] (positive/negative) input]
1: 0 to ± 10V
Sets the frequency when 10 V is
input as a percentage of the maxi input, as a percentage of the maxi-
mum output frequency.
Sets the frequency when 0 V is in-
put, as a percentage of the maxi- put as a percentage of the maxi
mum frequency.
0: 0 to + 10V [11-bit + polarity
(positive/negative) input] (positive/negative) input]
1: 0 to ± 10V
Select from the functions listed in
the following table. Refer to page the following table. Refer to page
7 - 79.
Sets the input gain (level) when
terminal 16 is 10 V. terminal 16 is 10 V.
Set according to the 100% value
on page 7 - 79.
Sets the input gain (level) when
terminal 16 is 0 V. terminal 16 is 0 V.
Set according to the 100% value
on page 7 - 79
0: 0 to +10 V (Always cut jump-
er wire J1)
1: 0 to ±10 V (Always cut jump- 1: 0 to ±10 V (Always cut jump-
er wire J1)
2: 4 to 20 mA (10-bit input)
Set as for H3-05.
:Cannot be set to 0. The 1F func-
tion will become "frequency ti ill b "f
reference."
Sets the input gain (level) when
terminal 14 is 10 V (20 mA).
Set according to the 100% value Set according to the 100% value
on page 7 - 79.
If H3-09 = "1F" the setting in
H3-02 is used.
Sets the input gain (level) when
terminal 14 is 0 V (4 mA).
Set according to the 100% value Set according to the 100% value
on page 7 - 79.
If H3-09 = "1F" the setting in
H3-03 is used.
Sets terminals 13, 14, 16 to prima-
ry delay filter time constant, in se-
conds units conds units.
:Effective for noise control etc.
8 - 31
8.2 Programming Mode Constants
Change Change
Setting S Factory during
Opera-
Range Setting
V/f
tion
B B
0, 1 0, 1 0 0
× ×
0.0 to 0.0 to
B B
100.0 100 0
f f
1000.0
− 100.0
B B
to to 0.0 0 0
f f
+ 100.0
B B
0, 1 0, 1 0 0
× ×
0 to 1F 0 to 1F 0 0 B B
× ×
0.0 to 0.0 to
B B
100 0 100.0
f f
1000.0
− 100.0
to to 0 0 0.0 B B
f f
+ 100.0
A A
0 to 2 0 to 2 2 2
× ×
A A
1 to 1F 1 to 1F 1F 1F
× ×
0.0 to 0.0 to
A A
100.0 100 0
f f
1000.0
− 100.0
A A
to to 0.0 0 0
f f
+ 100.0
0.00 to
A A
0.00 0.00
× ×
2.00 2 00
Control Methods
V/f
Page
Open
Flux
with
Loop
Vector
Vector
PG
B B B B B B
6 4 6 - 4
B B B B B B
6 - 7 6 7
B B B B B B
6 7 6 - 7
B B B B B B
6 7 6 - 7
B B B B B B 7 79 7 - 79
B B B B B B
6 - 7 6 7
B B B B B B 6 - 7 6 7
A A A A A A
6 4 6 - 4
A A A A A A
7 - 79 7 79
A A A A A A
6 7 6 - 7
A A A A A A
6 - 7 6 7
A A A A A A
6 7 6 - 7
8