Multi-Function Selections: O2 - YASKAWA VARISPEED-616G5 Instruction Manual

User Constants
8.2.8 Operator Constants: o
Constant C
Number
LOCAL/REMOTE key
enable/disable
o2 01 o2-01
Local/remote key
STOP key during
control circuit terminal
operation
o2-02
Oper STOP Key
User constant initial
value
o2-03 o2 03
User Defaults
kVA selection
o2-04 o2-04
Inverter Model #
Frequency reference
setting method selec-
tion
o2-05
Operator M.O.P.
8
Operation selection
when digital operator
is disconnected
o2-06
Oper Detection
Cumulative operation
time setting
o2-07 o2 07
Elapsed Time Set
Cumulative operation
time selection
o2-08 o2 08
Elapsed Time Run
Initialize mode selec-
tion
o2 09 o2-09
Init Mode Sel
* The factory setting depends upon the Inverter capacity. The values for a 200 V class Inverter of 0.4 kW will be displayed.

Multi-function Selections: o2

J
Name
Description
Display
Sets the Digital Operator Local/
Remote Key
0: Disabled
1: Enabled (Switches between 1 E bl d (S i h
the Digital Operator and the
constant settings.)
Sets the Stop Key in the run
mode.
0: Disabled (When the run com-
mand is issued from and exter-
nal terminal, the Stop Key is nal terminal, the Stop Key is
disabled.)
1: Enabled (Effective even dur-
ing run.)
Clears or stores user initial values.
0: Stores/not set
1: Begins storing (Records the
set constants as user initial val-
ues.)
2: All clear (Clears all recorded 2: All clear (Clears all recorded
user initial values)
:When the set constants are re-
corded as user initial values,
1110 will be displayed in the
Initialize mode (A1-03.)
Do not set. Do not set
When the frequency reference is
set on the Digital Operator fre-
quency reference monitor, sets
whether the Enter Key is neces-
sary.
0: Enter Key needed 0: Enter Key needed
1: Enter Key not needed
:When set to 1, the Inverter ac-
cepts the frequency reference
without Enter Key operation.
Sets the operation when the Digi-
tal Operator is disconnected.
0: Disabled (Operation continues
even if the Digital Operator is
disconnected.)
1: Enabled (OPR is detected at bl d (
Digital Operator disconnec-
tion. Inverter output is cut off,
and fault contact is operated.)
Sets the cumulative operation time
in hour units.
:Operation time is calculated ti ti
:O
from the set values.
0: Cumulative time when the In-
verter power is on. (All time
while the Inverter power is on
is accumulated.) s accu u ated.)
1: Cumulative Inverter run time.
(Only Inverter output time is
accumulated.)
Do not set. Do not set.
Setting S Factory
Range Setting
0, 1 0, 1 1 1
b
0, 1 1
0 to 2 0 to 2 0 0
0 to FF 0 to FF
0 * 0 *
*
0, 1 0
0, 1 0
i d d
0 to
0 0
65535 65535
i l l t d
0, 1 0, 1 0 0
0 to 2 0 to 2 0 0
8 - 44
Control Methods
Change Change
during
V/f
Open
Opera-
V/f with
Loop
tion Vector
Vector
PG
B B B B B B
× ×
B B B
×
B B B B B B
× ×
B B B B B B
× ×
A A A
×
A A A
×
A A A A A A
× ×
A A A A A A
× ×
A A A A A A
× ×
Page
Flux
B B
7 - 98 7 98
B 7 - 99
B B
7 - 99 7 99
B B
7 - 99 7 - 99
A 7 - 99
A 7 - 100
A A 7 100 7 - 100
A A
7 100 7 - 100
A A
−