Common Functions; Functions Used With All Control Methods - YASKAWA VARISPEED-616G5 Instruction Manual

7.5 Common Functions

The functions that can be used for all control methods are listed in Table 7.5. Details on functions marked with
a L are provided in the following table.
Table 7.5
Group
b1 Sequence
b2 DC Injection Braking
b3 Speed Search
b4 Delay Timers
b5 PID Control
b Application b Application
b6 Dwell Functions
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Compensation
C4 Torque Compensation
C Tuning C Tuning
C5 Speed Controls
C6 Carrier Frequency
C7 Hunting Prevention
C8 Factory Tuning
d1 Preset Reference
d2 Reference Limits
d3 Prohibited Frequencies
d Reference d Reference
Reference Frequence Hold
d4
Functions
d5 Torque Control
E1 V/f Pattern
E2 Motor Setup
E3 Motor 2 Control Methods
E Motor E Motor
E4 Motor 2 V/f Characteristics
E5 Motor 2 Motor Constants
PG Speed Control Card
F1
Settings
F2 Analog Reference Card AI
F3 Digital Reference Card DI
F4 Analog Monitor Card AO
F5 Digital Output Card DO
F Options F Options
F6 Digital Output Card DO
F7 Pulse Monitor Card PO
SI-F/SI-G Transmission
F8
Card
Transmission Cards other
F9
than SI-K2 and SI-F/G
H1 Multi-function Inputs
H2 Multi-function Outputs
H3 Analog Inputs
H Terminal H T i l
Multi-function Analog Out-
H4
puts
MEMOBUS Communica-
H5
tions

Functions Used with All Control Methods

Function
Settings such as the reference input method
L DC injection braking function settings
L Speed search function settings
L Timer function settings
L PID control settings
L Acceleration/deceleration time dwell function settings
Droop control settings
Multi-function input: Sets energy-saving control by energy saving
reference.
Zero servo settings
Acceleration/deceleration time settings
L S-curve characteristics for acceleration/deceleration times
L Slip compensation function settings
L Torque compensation function settings
Speed control tuning
L Carrier frequency settings
Hunting prevention settings
Adjustment for open-loop vector control
Frequency reference settings (when using Operator)
L Frequency upper and lower limit settings
L Prohibited frequency settings
L Up/Down, Accel/Decel stop hold frequency setting
Torque control settings and tuning
Motor constant settings Motor constant settings
Control method settings for motor 2.
V/f characteristics settings for motor 2.
Motor constant setting for motor 2.
Constant settings for a PG Speed Control Card
User constant settings for an Analog Reference Card
L
User constant settings for a Digital Reference Card
L
User constant settings for an Analog Monitor Card
L
User constant settings for a Digital Output Card
User constant settings for a Digital Output Card
User constant settings for a Pulse Monitor Card
L
User constant settings for a Transmission Card
User constant settings for a Transmission Card
Function selection for multi-function inputs
L
Function selection for multi-function outputs
L
Function selection for analog inputs
L
Function selection for analog outputs
L
MEMOBUS communications settings
7 - 41
7.5 Common Functions
Comments
Control Meth-
od
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
× × ×
f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
×
f f f
× ×
f f
f f f f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
× × ×
f
7
f f f f
f f f f
f f f f
f f f f
f f f f
× × f
f
f f f f
f f f f
f f f f
f f f f
f
f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
− − − −