Flux Vector Control Functions - YASKAWA VARISPEED-616G5 Instruction Manual

Advanced Operation
7.3 Flux Vector Control
Group
b Application b Application
C Tuning C Tuning
d Reference d Reference
7
E Motor E Motor
F Options F Options
H T H Terminal i l
The functions that can be used with flux vector control are listed in Table 7.3. Details on functions that are spe-
cific to flux vector control (i.e. those marked with a L) are provided in the following table.
Table 7.3

Flux Vector Control Functions

Function
b1 Sequence
b2 DC Injection Braking
b3 Speed Search
b4 Delay Timers
b5 PID Control
b6 Dwell Functions Hold
b7 Droop Control
b8 Energy Saving
b9 Zero Servo
C1 Accel/Decel
C2 S-Curve Acc/Dec
C3 Motor-Slip Compensation
C4 Torque Compensation
C5 Speed Controls
C6 Carrier Frequency
C7 Hunting Prevention
C8 Factory Tuning
d1 Preset Reference
d2 Reference Limits
d3 Jump Frequencies
Reference frequency hold
d4
function
d5 Torque Control
E1 V/f Pattern
E2 Motor Setup
E3 Motor 2 Control Methods
E4 Motor 2 V/f Characteristics
E5 Motor 2 Motor Constants
PG Speed Control Card
F1
Settings
F2 Analog Reference Card AI
F3 Digital Reference Card DI
F4 Analog Monitor Card AO
F5 Digital Output Card DO
F6 Digital Output Card DO
F7 Pulse Monitor Card PO
SI-F/SI-G Transmission
F8
Card
Transmission Cards other
F9
than SI-K2 and SI-F/G
H1 Multi-function Inputs
H2 Multi-function Outputs
H3 Analog Inputs
Multi-function Analog Out-
H4
puts
MEMOBUS Communica-
H5
tions
Comments
Settings such as the reference input method
DC injection braking function settings
Speed search function settings
Timer function settings
PID control settings
Acceleration/deceleration time dwell function settings
L Droop Control function settings
Not used. (Can't be set.)
L Zero-servo function settings
Acceleration/deceleration time settings
S-curve characteristics for accel/decel times
L Motor temperature compensation function adjustment
Not used. (Can't be set.)
Speed control loop adjustment
Carrier frequency settings
Not used. (Can't be set.)
Not used. (Can't be set.)
Frequency reference settings (when using Operator)
Frequency upper and lower limit settings
Prohibited frequency settings
Up/Down, Accel/Decel stop hold frequency setting
L Torque control settings and adjustment
Motor constant settings Motor constant settings
L L
(Motor constants set automatically with autotuning.)
Control method settings for motor 2.
V/f characteristics settings for motor 2.
Motor constant settings for motor 2.
Constant settings for a PG Speed Control Card
User constant settings for an Analog Reference Card
User constant settings for a Digital Reference Card
User constant settings for an Analog Monitor Card
User constant settings for a Digital Output Card
User constant settings for a Digital Output Card
User constant settings for a Pulse Monitor Card
User constant settings for a Transmission Card
User constant settings for a Transmission Card
Function selection for multi-function inputs
Function selection for multi-function outputs
Function selection for analog inputs
Function selection for analog outputs
MEMOBUS communications settings
7 - 16
Control Meth-
od
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
× × ×
f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
×
f f f
× ×
f f
f f f f
× ×
f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
× × ×
f
f f f f
f f f f
f f f f
f f f f
f f f f
× ×
f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f
f f f f