Panasonic FP-X0 L14R User Manual page 261

Num-
Name
ber
F150 Data read from
P150 intelligent unit
F151 Data write into
P151 intelligent unit
F152 Data read from
P152 MEWNET-F
slave station
F153 Data write into
P153 MEWNET-F
slave station
F155 Sampling
P155
F156 Sampling trigger STRG
P156
F157 Time addition
P157
F158 Time subtraction CSUB
P158
F159 Serial port
P159 communication
F161 MCU serial port
P161 reception
BIN arithmetic instruction
F160 Double word
P160 (32-bit) data
square root
High speed counter/Pulse output instruction for FP0, FP-e
F0 High-speed
counter and
Pulse output
controls
1 Change and
read of the
elapsed value of
high-speed
counter and
Pulse output
F166 Target value
much on
: Available, : Not available,
*1) The instruction is available for FP0 T32 (V2.3 or later) and FP-e.
*2) This instruction is available for FPΣ Ver. 2.0 or later.
*3) This instruction is available for FPΣ Ver. 3.10 or later.
*4) This instruction is only available for FP-X Ver.2.0 or later.
*5) Available for FP-X0 L40 and L60 types only.
*6) The instruction is available for FP2/FP2SH Ver. 1.5 or later, and the pulse execution type can be specified.
FP10SH cannot be used.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Boolean Ope-rand
READ S1, S2, n, Reads the data from the
PREAD D intelligent unit.
WRT S1, S2, n, Writes the data into the intelligent
PWRT D unit.
RMRD S1, S2, n, Reads the data from the
PRMRD D intelligent unit at the MEWNET-F
(remote I/O) slave station.
RMWT S1, S2, n, Writes the data into the intelligent
PRMWT D unit at the MEWNET-F (remote
I/O) slave station.
SMPL - Starts sampling data.
PSMPL
- When the trigger of this
PSTRG instruction turns on, the sampling
trace stops.
CADD S1, S2, D The time after (S2+1, S2)
PCADD elapses from the time of (S1+2,
S1+1, S1) is stored in (D+2, D+1,
D).
S1, S2, D The time that results from
PCSUB subtracting (S2+1, S2) from the
time (S1+2, S1+1, S1) is stored
in (D+2, D+1, D).
MTRN S, n, D This is used to send data to an
PMTRN external device through the
specified CPU COM port or MCU
COM port.
MRCV S, D1, D2 Data is received from external
PMRCV equipment via the COM port of
the specified MCU.
DSQR S, D
√(S)→(D)
PDSQR
MV S, Performs high-speed counter and
DT9052 Pulse output controls according
to the control code specified by
"S". The control code is stored in
DT9052.
DMV S, Transfers (S+1, S) to high-speed
DT9044 counter and Pulse output elapsed
value area.
DT9044, Transfers value in high-speed
D counter and Pulse output elapsed
value area to (D+1, D).
HC1S n, S, Yn Turns output Yn on when the
elapsed value of the built-in high-
speed counter reaches the target
value of (S+1, S).
: Not available partially
Description
9
9
9
9
1
1
9
9
7
7
7
5
7
7
11
*2
*2
*3 *4 *5
*3 *4 *5
*1
*1
*6
*6
- - - - -
- - - - -
- - - - -
- - - - -
*6
*6
-
-
-
-