Table of Contents
Advertisement
QUICK INSTALLATION GUIDE
Please read the Safety Information in the "Printer Reference" before using this machine.
It contains important information related to USER SAFETY and PREVENTING EQUIP-
MENT PROBLEMS.
UNPACKING THE PRINTER AND
Caution
• Keep the machine away from humidity and dust.
CHECKING THE CONTENTS OF
A fire or an electric shock might occur.
THE BOX
• Place the machine on a strong and level surface.
Otherwise, the machine might fall and cause
personal injury.
Caution
• If you use the machine in a confined space,
• To prevent injury, this printer should be lifted by
confirm that there is a continuous flow of air.
at least three people.
Optimum Environmental Conditions
Check the contents of the box according to the
following list. If one or some items are missing,
Recommended temperature and humidity
please contact your sales or service
RH
80
representative.
60
Important
The parallel cable is not included in the box. It is
40
your responsibility to provide the parallel cable
appropriate for the computer you are using.
20
Quick Installation Guide (this sheet)
10
Setup Guide
RH
Output Tray Extender
80
Fuser Oil Bottle
60
CD-ROM
40
Power Cord
Printer (including a starter toner cartridge)
20
50
Additional Documentation
Remove the plastic bag.
The machine must be level within 5 mm, 0.2" both front to rear
and left to right.
Lift the printer and move it to the place where
To avoid possible build-up of ozone, locate this printer in a large well
you want to install it.
ventilated room that has an air turnover more than 30 m 3 /hr/person.
When lifting the printer, use the inset grips on both sides of the
If you use this printer in a cold area, leave the printer on or severe
printer.
cold might damage sensitive components inside the printer.
Environments to Avoid
3
6
Locations exposed to direct sunlight or strong light
2
Dusty areas
1
5
Areas with corrosive gases
4
ZBGH160E
Areas excessively cold, hot, or humid
Important
Locations near an air conditioner or humidifier
Locations near other electronic equipment
Be careful when lifting the printer as the front right
side is significantly heavier than the front left side.
Locations where the printer might be subjected to
Do not grip the part joining Tray 1 and the duplex
frequent strong vibration
tray.
Power Connection
Connect the power cord to a power source with the following specifications:
220-240 V, 50/60 Hz, 5.2 A or more
Space Required for Installing the Printer
Leave enough space around the printer. This space is necessary to
WHERE TO PUT THE PRINTER
operate the printer. The recommended (or minimum) space
requirement is as follows:
The printer's location should be carefully chosen
because environmental conditions greatly affect its
performance.
Warning
• Confirm that the wall outlet is near the machine
and freely accessible, so that in event of an
emergency, it can be unplugged easily.
• Only connect the machine to the power source
described on this sheet.
• Avoid multi-wiring.
• Do not damage, break or make any
A: more than 5 cm (2.0")
B: more than 10 cm (4.0")
modifications to the power cord. Do not place
heavy objects on it, pull it hard or bend it more
C: more than 70 cm (27.6")
than necessary. These actions could cause an
D: more than 65 cm (25.6")
electric shock or fire.
<G048-8610>
REMOVING THE TAPES,
PROTECTIVE SHEET AND
PADDING FROM THE PRINTER
Remove the fifteen tapes that holds the outside
covers closed.
10
80
27
80
15
25
32
70
70
54
15
25
30
30
10
20
32
20
20
30
50
80
80.6
80
59
77
89.6
70
70
54
59
77
30
30
Pull the duplex tray out, and then remove the
50
20
89.6
20
three tapes that fixes the paper guides in the
60
70
80
90
duplex tray.
Possible operation range
Recommended range
Push the front cover release button and open
the front cover.
Important
Holding the green inset grips of the
photoconductor unit, pull the top side of the unit
forward.
A
D
B
C
ZBGX080E
Pull the red tab to remove the protective sheet
from the new photoconductor unit.
ZBGH101E
Important
Be careful to prevent the green film in the
photoconductor unit from becoming dirty or
damaged, and do not touch the black belt in the
ZBGH062E
unit. The condition of these components directly
affects output quality.
Do not rotate the gear on the right side of the
photoconductor unit or the inside belt will be
damaged.
The white powder on the photoconductor unit is
to protect it after installation into the printer. This
white powder does not have any adverse effect on
the interior of the printer.
ZBGH140E
Remove the packing marked with a red tab
inside the printer on the left.
ZBGH110E
ZBGH150E
Holding the green inset grips of the
photoconductor unit, push the unit back to its
original position.
ZBGH071E
ZBGH091E
Close the front cover.
Confirm that the front cover closes properly.
ZBGH092E
Remove the one piece of padding and two tapes.
INSTALLING THE FUSER OIL
BOTTLE
Caution
• Do not incinerate the oil bottle. This action could
cause a fire or getting burned.
• Spilt oil is very slippery. If oil is spilt, wipe it with
alkaline cleaner. Otherwise, the oily surfaces can
create the danger of slipping and personal injury.
Slide the paper guides to adjust them to the paper
width.
Remove the green cap from the new oil bottle.
Adjust the paper guides until they click into position.
Important
Hold the clear cap while turning the green cap. Do
not remove the clear cap.
Important
TFWX035E
Do not touch the friction pad (A) or paper misfeeds
Open the fuser oil bottle cover of the printer.
or multi-feeds might occur.
Note
The factory default setting is A4 L.
Load paper into the tray with the side to be printed
onto face up.
ZBGH130E
Insert the new oil bottle into the oil bottle case.
Important
Confirm that the top of the stack is no higher than
the limit mark (
ZBGH131E
Confirm that paper fits under the rear guide.
Close the fuser oil bottle cover.
Do not mix different kinds of paper in the tray.
Adjust the paper size dial to match the paper size
and feed direction.
INSTALLING THE PAPER
TRAY AND OUTPUT TRAY
Slide the paper tray into the printer until it stops.
EXTENDER
Important
The following procedure describes how to load
Be sure to insert the paper tray completely or paper
A4L.
misfeeds might occur, or the front cover might touch
For more information about the paper sizes that
the paper tray.
can be set in the paper tray, see "Paper and
Insert the output tray extender into the output tray.
Other Media Supported by This Printer" in the
"Printer Reference" included as a PDF file on
the CD-ROM.
Slide the paper tray out until it stops. Lift it
slightly then slide it out of the printer. Place it
on a flat surface.
TFWY015E
A
TFWY035E
TFWY045E
) inside the tray.
TFWY055E
ZBGH021E
Advertisement
Chapters
Table of Contents
