Lenovo x3550 M4 Installation And Service Manual page 444

806f050c-2015ffff • 806f050c-2016ffff
implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2014ffff or
0x806f050c2014ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.
7. (Trained technician only) Replace the affected
microprocessor.
806f050c-2015ffff Memory Logging Limit Reached
for [PhysicalMemoryElementName] on
Subsystem [MemoryElementName].
(DIMM 21)
Explanation: This message is for the use case when an
implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2015ffff or
0x806f050c2015ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
426
System x3550 M4 Type 7914: Installation and Service Guide
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.
7. (Trained technician only) Replace the affected
microprocessor.
806f050c-2016ffff Memory Logging Limit Reached
for [PhysicalMemoryElementName] on
Subsystem [MemoryElementName].
(DIMM 22)
Explanation: This message is for the use case when an
implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2016ffff or
0x806f050c2016ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.