Lenovo x3550 M4 Installation And Service Manual page 439

implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2006ffff or
0x806f050c2006ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.
7. (Trained technician only) Replace the affected
microprocessor.
806f050c-2007ffff Memory Logging Limit Reached
for [PhysicalMemoryElementName] on
Subsystem [MemoryElementName].
(DIMM 7)
Explanation: This message is for the use case when an
implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2007ffff or
0x806f050c2007ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
806f050c-2007ffff • 806f050c-2008ffff
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.
7. (Trained technician only) Replace the affected
microprocessor.
806f050c-2008ffff
Explanation: This message is for the use case when an
implementation has detected that the Memory Logging
Limit has been Reached.
May also be shown as 806f050c2008ffff or
0x806f050c2008ffff
Severity: Warning
Alert Category: Warning - Memory
Serviceable: Yes
CIM Information: Prefix: PLAT and ID: 0144
SNMP Trap ID: 43
Automatically notify Support: Yes
User response:
1. Refer to TIP H212293 for minimum code level.
2. Check the IBM support website for an applicable
retain tip or firmware update that applies to this
memory error.
3. Swap the affected DIMMs (as indicated by the
error LEDs on the system board or the event logs)
to a different memory channel or microprocessor.
4. If the error still occurs on the same DIMM, replace
the affected DIMM.
5. (Trained technician only) If the problem occurs on
the same DIMM connector, check the DIMM
connector. If the connector contains any foreign
material or is damaged, replace the system board.
6. (Trained technician only) Remove the affected
microprocessor and check the microprocessor socket
pins for any damaged pins. If a damage is found,
replace the system board.
Appendix A. Integrated management module II (IMM2) error messages
Memory Logging Limit Reached
for [PhysicalMemoryElementName] on
Subsystem [MemoryElementName].
(DIMM 8)
421