Table of Contents
Advertisement
Remote Control Operation
Interface
Command:
Substitute
Response:
Pattern
(Transmit
Status:
2047
Response:
Pattern)
Interface
Command:
Read Error
Response:
Select
(Receive
Status:
2047
Response:
Pattern)
Interface
Command:
Service
Response:
Channel
Level
Status:
Response:
Interface
Command:
Transmit
Response:
Overhead
Type
Status:
Response:
Interface
Command:
Receive
Response:
Overhead
Type
Status:
Response:
Transmit
Command:
Data Phase
Response:
Status:
Response:
Receive
Command:
Data Phase
Response:
Status:
Response:
IDR
Command:
Backward
Response:
Alarm
Enable
Status:
Response:
Scrambler
Command:
Type
Response:
Status:
Response:
Descramble
Command:
r Type
Response:
Status:
Response:
B–8
<add/ISP_xxx'cr'
>add/ISP_xxx'cr''lf']
<add/ISP_'cr'
>add/ISP_xxx'cr''lf']
<add/IRE_xxx'cr'
>add/IRE_xxx'cr''lf']
<add/IRE_'cr'
>add/IRE_xxx'cr''lf']
<add/ISCL_xxx_nnn'cr'
>add/ISCL_xxx_nnn'cr''lf']
<add/ISCL_xxx'cr'
>add/ISCL_xxx_nnn'cr''lf']
<add/ITOT_xxxx'cr'
>add/ITOT_xxxx'cr''lf']
<add/ITOT_'cr'
>add/ITOT_xxxx'cr''lf']
<add/IROT_xxxx'cr'
>add/IROT_xxxx'cr''lf']
<add/IROT_'cr'
>add/IROT_xxxx'cr''lf']
<add/TDP_xxxx'cr'
>add/TDP_xxxx'cr''lf']
<add/TDP_'cr'
>add/TDP_xxxx'cr''lf']
<add/RDP_xxxx'cr'
>add/RDP_xxxx'cr''lf']
<add/RDP_'cr'
>add/RDP_xxxx'cr''lf']
<add/BW_xxx_nnn'cr'
>add/BW_xxx_nnn'cr''lf']
<add/BW_xxx_'cr'
>add/BW_xxx_nnn'cr''lf']
<add/SCRT_xxxx'cr'
>add/SCRT_xxxx'cr''lf']
<add/SCRT_'cr'
>add/SCRT_xxxx'cr''lf']
<add/DSCT_xxxx'cr'
>add/DSCT_xxxx'cr''lf']
<add/DSCT_'cr'
>add/DSCT_xxxx'cr''lf']
Where: xxx = ON or OFF.
Where: xxx = ON or OFF.
Where:
xxx = TX1, TX2, RX1, or RX2 (service channel designator).
nnn = -20 to +10, in steps of 1 (service channel level in
dBm).
Where: xxxx = NONE or IDR.
Note: If the ESC Option is not installed, only 'NONE' will be
allowed.
Where: xxxx = NONE or IDR.
Note: If the ESC Option is not installed, only 'NONE' will be
allowed.
Where: xxxx = NRM (normal data phasing) or INV (inverted
data phasing).
Where: xxxx = NRM (normal data phasing) or INV (inverted
data phasing).
Where:
xxx = TX1, TX2, TX3, TX4, RX1, RX2, RX3, or RX4
(backward alarm designator).
nnn = ON or OFF.
Where: xxxx = V.35, EFD, or IDR.
Where: xxxx = V.35, EFD, or IDR.
SDM-9000 Satellite Modem
Rev. 4
Advertisement
Table of Contents
