Editing A Repeater List; Duplex Direction Setting (Dup); Frequency Offset Programming (Offset)/Storing The Repeater List; Repeater List Selection/Repeater Data Programming - Icom IC-9100 Instruction Manual

7
DV MODE PROGRAMMING
Repeater list programming (Continued)
8.
This content appears when "
USE" as described in 'Access repeater setting (R1
USE)' on page 90.
#1 Push [Z](F-2) to display the "DUP" item (Duplex di-
rection setting).
RP–L D U P
#2 Rotate [MAIN DIAL] to select the duplex direction.
OFF : The duplex function is OFF.
DUP– : The transmit frequency shifts down from the re-
ceive frequency by the offset amount.
DUP+ : The transmit frequency shifts up from the re-
ceive frequency by the offset amount.
9.
This content appears when "
USE" as described in 'Access repeater setting (R1
USE)' on page 90.
#3 Push [Z](F-2) to display the "OFFSET" item (Fre-
quency offset Programming).
RP–L O F F S E T :
#4 Rotate [MAIN DIAL] to select the frequency offset.
played frequency offset.
10.
#5 Push [Z](F-2) to display the "ADD Write" item (Re-
peater list Storing).
ADD
RP–L
Ù
#6 Hold down [WR](F-5) to store the entry.
ADD W r i t e O K ?
RP–L
Ù
#7 Hold down
to the RP-L screen.
91
" is selected in "R1
: OFF
" is selected in "R1
0 . 0 0 0 . 0
C L R
W r i t e
Ú
W R
Ú
Y E S N O
This function re-programs a repeater's data. This is
useful when already-programmed data is incorrect or
some data should be added to the list.
1.
q Push [DV DR] to select the DV mode.
w Push [MENU] one or more times to display the "M3"
screen (Menu 3).
M3
CS C D
e Push [DSET](F-5) to display the "DSET" screen.
DSET
r Push [RP-L](F-4) to display the "RP-L" screen (Re-
peater list).
R e p e a t e r
RP–L
t Push [EDT](F-5) to display the repeater list.
RP–L HAMACH43
E D T
y Rotate [MAIN DIAL] to select the desired repeater
to be changed.
RP–L KOUTOU43
E D T
Hold down [GRP](F-5) for 1 second to enter the
repeater group selection mode. ("≈" moves next
-
to the repeater group name, and then blinks.)
Rotate [MAIN DIAL] to select the desired group (0
to 9), then push [GRP](F-5).
Or, you can select the repeater group using the
keypad key.
"SEL" appears when "R1 USE" setting is set to
" " The selected repeaters can be used as an
access repeater (R1) in the DR mode, and are
scanned during an access repeater scan.
2.
u Push [EDT](F-1) to enter the repeater data pro-
gramming mode.
i Push [Y](F-1) or [Z](F-2) to select the item to be
changed.
o Program the selected item data. See pages 89–91
for new repeater list programming details.
N A M E :
RP–L
Ù Ú
If you are reprogramming a repeater with its
own gateway, you must also edit the gateway re-
peater call sign.
R > C S U R DSET
T X M R P — L S E T
L i s t
C L R A D D E D T
GRP1
SEL
SEL GRP
GRP1
SEL
SEL GRP
[SEL](F-4).
KOUTOU43
E D T