Yamaha XT1200Z(Z) 2010 Service Manual page 81

Item
Oil pipe bolt
Oil pump assembly bolt
Oil pump housing cover bolt
Oil strainer (oil pump) bolt
Main axle assembly bolt
Shift drum retainer screw
Shift shaft spring stopper bolt
Connecting rod nut
Middle gear side cover screw
Middle gear side cover damper
plate screw
Engine oil drain bolt (middle
gear)
Middle driven pinion gear bearing
housing bolt
Middle drive pinion gear bearing
retainer bolt
Middle drive pinion gear nut
Starter motor assembly bolt
Starter motor terminal nut
Starter motor front cover bolt
Starter motor terminal and rear
cover nut
TIP
Cylinder head bolt
Tighten the cylinder head bolts "1"–"8" in the proper tightening sequence as follows:
• Tighten the cylinder head bolts "1"–"6" to 20 Nm (2.0 m·kgf, 14 ft·lbf).
• Tighten the cylinder head bolts "1"–"6" to 30 Nm (3.0 m·kgf, 22 ft·lbf), and then tighten them further to
reach the specified angle. Tighten each bolt to the specified angle before tightening the next bolt to
30 Nm (3.0 m·kgf, 22 ft·lbf).
"1", "2", "4": 215–225°
"3", "5", "6": 180–190°
• Tighten the cylinder head bolts "7" and "8" to 10 Nm (1.0 m·kgf, 7.2 ft·lbf).
Thread
Q'ty
size
M6 3
M6 3
M6 6
M6 3
M6 3
M6 2
M8 1
M9 4
M6 6
M6 2
M8 1
M8 4
M8 4
M44 1
M6 2
M6 1
M5 2
M6 1
1
3
5
2
2-20
TIGHTENING TORQUES
Tightening torque
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
22 Nm (2.2 m·kgf, 16 ft·lbf)
See TIP.
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
20 Nm (2.0 m·kgf, 14 ft·lbf)
33 Nm (3.3 m·kgf, 24 ft·lbf)
28 Nm (2.8 m·kgf, 20 ft·lbf)
110 Nm (11 m·kgf, 80 ft·lbf)
12 Nm (1.2 m·kgf, 8.7 ft·lbf)
5 Nm (0.5 m·kgf, 3.6 ft·lbf)
5 Nm (0.5 m·kgf, 3.6 ft·lbf)
11 Nm (1.1 m·kgf, 8.0 ft·lbf)
6
8
7
4
Remarks
LT
LT
LT
LT
M
LT
LT
LT
LT
Stake.