Table of Contents
Advertisement
Remote Control Operation
Change
Command:
Status
Response:
Equipment
Command:
Type
Response:
Monitor &
Command:
Control
Response:
Firmware
Information
DATA ROM
Command:
Firmware
Response:
Information
Interface
Command:
Type
Response:
Bulk Consol
Command:
Status
Response:
AUPC
A–26
<add/CS_'cr'
>add/CS_x'cr''lf']
<add/ET_'cr'
>add/ET_tttttttt_xxx.yyy.zzz'cr''lf']
<add/MCFI_'cr'
>add/MCFI_'cr'
VER_xxx.yyy.zzz'cr'
FW/nnnnnn-ddr'cr'
mm/dd/yy'cr''lf']
<add/DFI_'cr'
>add/DFI_'cr'
DSP_FW/nnnnnn-ddr'cr'
DSP_mm/dd/yy'cr'
FPGA_FW/nnnnnn-ddr'cr'
FPGA_mm/dd/yy'cr''lf']
<add/IT_'cr'
>add/IT_ttttt'cr''lf']
<add/BCSA_'cr'
>add/BCSA_p1,p2,p3, . . . pn'cr''lf']
SDM-100A Satellite Modem
Where: The 'x' character is defined as follows:
'@' = no change since last BCS_ and BCSF_ polls.
'A' = BCS_ response has changed since last BCS_ poll.
'B' = BCSF_ response has changed since last BCSF_
poll.
'C' = Both responses have changed since last BCS_
and BCSF_ polls.
This command indicates that a change has or has not
occurred on either the BCS_ or the BCSF_ response since
the last BCS_ or BCSF_ poll.
Where:
tttttttt = Equipment type.
xxx.yyy.zzz = Software version.
This command returns the equipment type and the
software version of the addressed device.
Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999).
nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Where:
nnnnnn = Firmware number (0 to 999999).
dd = Firmware dash number (0 to 99).
r = Firmware revision (-, or A to Z).
Where: ttttt = RS422, V.35, RS232, ADPCM, or ASYNC.
This command returns the Interface equipment type.
Where 'pn' is the last parameter returned.
Parameter 1 (p1): Local AUPC enable ON/OFF.
p1 = n, where 'n' is '0' (off) or '1' (on).
Parameter 2 (p2): Nominal Power Value.
p2 = snn.n, where 'snn.n' Nominal Power Value in dBm.
Parameter 3 (p3): Minimum Power Value.
p3 = snn.n, where 'snn.n' Minimum Power Value in
dBm.
Parameter 4 (p4): Maximum Power Value.
p4 = snn.n, where 'snn.n' Maximum Power Value in
dBm.
Parameter 5 (p5): E
/N
Target Set Point.
b
0
p5 = n.n, where 'n.n' E
/N
b
Parameter 6 (p6): Max. Tracking Rate.
p6 = n.n, where 'n.n' is the Max. Tracking Rate in
dB/Min.
Parameter 7 (p7): Local Carrier Loss.
p7 = n, where 'n' is '0' (HOLD), '1' (NOMINAL), or '2'
(MAXIMUM).
Parameter 8 (p8): Remote Carrier Loss.
p8 = n, where 'n' is '0' (HOLD), '1' (NOMINAL), or '2'
(MAXIMUM).
Target Set Point in dB.
0
Rev. 0
Advertisement
Table of Contents
