Table of Contents
Advertisement
SDM-100A Satellite Modem
Interface
Command:
Subscriber/
Response:
Trunk
Emulation
Status:
Response:
E & M
Command:
Signal Type
Response:
Status:
Response:
Interface
Command:
Encoding
Response:
Law
Status:
Response:
Off Hook
Command:
Alert Enable
Response:
Status:
Response:
Interface
Command:
Service
Response:
Channel
Level
Status:
Response:
Interface
Command:
RD Signal
Response:
Status:
Response:
Interface
Command:
SD Signal
Response:
Status:
Response:
Interface
Command:
RR Signal
Response:
Status:
Response:
Interface
Command:
DM Signal
Response:
Status:
Response:
Interface
Command:
ASYNC
Response:
Communi-
cations
Status:
Program
Response:
ASYNC
Command:
Transmit
Response:
Overhead
Baud Rate
Status:
Response:
Rev. 0
<add/SBTR_xxx'cr'
>add/SBTR_xxx'cr''lf']
<add/SBTR_'cr'
>add/SBTR_xxx'cr''lf']
<add/EMS_n'cr'
>add/EMS_n'cr''lf']
<add/EMS_'cr'
>add/EMS_n'cr''lf']
<add/LAW_y'cr'
>add/LAW_y'cr''lf']
<add/LAW_'cr
>add/LAW_y'cr''lf']
<add/HOOK_xxx'cr'
>add/HOOK_xxx'cr''lf']
<add/HOOK_'cr
>add/HOOK_xxx'cr''lf']
<add/ISCL_xx_nnn'cr'
>add/ISCL_xx_nnn'cr''lf']
<add/ISCL_xx'cr'
>add/ISCL_xx_nnn'cr''lf']
<add/RD_xxx'cr'
>add/RD_xxx'cr''lf']
<add/RD_'cr'
>add/RD_xxx'cr''lf']
<add/SD_xxx'cr'
>add/SD_xxx'cr''lf']
<add/SD_'cr'
>add/SD_xxx'cr''lf']
<add/RR_xxx'cr'
>add/RR_xxx'cr''lf']
<add/RR_'cr'
>add/RR_xxx'cr''lf']
<add/DM_xxx'cr'
>add/DM_xxx'cr''lf']
<add/DM_'cr'
>add/DM_xxx'cr''lf']
<add/ACP_xxx'cr'
>add/ACP_xxx'cr''lf']
<add/ACP_'cr'
>add/ACP_xxx'cr''lf']
<add/TOBR_nnnnn'cr'
>add/TOBR_nnnnn'cr''lf']
<add/TOBR_'cr'
>add/TOBR_nnnnn'cr''lf']
Where: xxx = SUB or TRK.
Note: Only valid when ADPCM board is installed.
Where: n = 1 to 5, in steps of 1.
Note: Only valid when ADPCM board is installed.
Where: y = A (A-Law) or U (u-Law).
Where: xxx = ON or OFF.
Note: Only valid when ADPCM board is installed.
Where:
xx = TX or RX (service channel designator).
nnn = -20 to +10, in steps of 1 (service channel level in
dBm).
Note: Only valid when ADPCM board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ADPCM board is installed.
Where: xxx = ON or OFF.
Note: Only valid when ASYNC board is installed.
Where: nnnnn = 150, 300, 600, 1200, or 2400.
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Remote Control Operation
A–9
Advertisement
Table of Contents
