Table of Contents
Advertisement
Remote Control Operation
ASYNC
Command:
Receive
Response:
Overhead
Baud Rate
Status:
Response:
ASYNC
Command:
Transmit
Response:
Channel
Character
Status:
Length
Response:
ASYNC
Command:
Receive
Response:
Channel
Character
Status:
Length
Response:
ASYNC
Command:
Transmit
Response:
Channel
Stop Bits
Status:
Response:
ASYNC
Command:
Receive
Response:
Channel
Stop Bits
Status:
Response:
ASYNC
Command:
Transmit
Response:
Overhead
Channel
Status:
Parity
Response:
ASYNC
Command:
Receive
Response:
Overhead
Channel
Status:
Parity
Response:
Interface
Command:
Loop Timing
Response:
ASYNC
Command:
Overhead
Response:
Communi-
cations
Status:
Type
Response:
Interface
Command:
Wire Type
Response:
Terrestrial
Command:
Communi-
Response:
cations
Type
Status:
Response:
Interface
Command:
SD Signal
Response:
Command
Interface
Command:
RS Signal
Response:
Command
A–10
<add/ROBR_nnnnn'cr'
>add/ROBR_nnnnn'cr''lf']
<add/ROBR_'cr'
>add/ROBR_nnnnn'cr''lf']
<add/TCCL_n'cr'
>add/TCCL_n'cr''lf']
<add/TCCL_'cr'
>add/TCCL_n'cr''lf']
<add/RCCL_n'cr'
>add/RCCL_n'cr''lf']
<add/RCCL_'cr'
>add/RCCL_n'cr''lf']
<add/TCSB_n'cr'
>add/TCSB_n'cr''lf']
<add/TCSB_'cr'
>add/TCSB_n'cr''lf']
<add/RCSB_n'cr'
>add/RCSB_n'cr''lf']
<add/RCSB_'cr'
>add/RCSB_n'cr''lf']
<add/TOCP_xxxx'cr'
>add/TOCP_xxxx'cr''lf']
<add/TOCP_'cr'
>add/TOCP_xxxx'cr''lf']
<add/ROCP_xxxx'cr'
>add/ROCP_xxxx'cr''lf']
<add/ROCP_'cr'
>add/ROCP_xxxx'cr''lf']
<add/ILT_xxx'cr'
>add/ILT_xxx'cr''lf']
<add/OCT_xxxxx'cr'
>add/OCT_xxxxx'cr''lf']
<add/OCT_'cr'
>add/OCT_xxxxx'cr''lf']
<add/IWT_xxx'cr'
>add/IWT_xxx'cr''lf']
<add/TCT_xxxxx'cr'
>add/TCT_xxxxx'cr''lf']
<add/TCT_'cr'
>add/TCT_xxxxx'cr''lf']
<add/ISSD_xxx'cr'
>add/ISSD_xxx'cr''lf']
<add/ISRS_xxx'cr'
>add/ISRS_xxx'cr''lf']
Where: nnnnn = 150, 300, 600, 1200, or 2400.
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: n = 5, 6, 7, or 8 (characters).
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: n = 5, 6, 7, or 8 (characters).
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: n = 1 or 2 (stop bits).
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: n = 1 or 2 (stop bits).
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: xxxx = ODD, EVEN, or NONE.
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: xxxx = ODD, EVEN, or NONE.
Note: Only valid when ASYNC board is installed with ASYNC
enabled.
Where: xxx = ON or OFF.
Where: xxxxx = RS232 or RS485.
Note: Only valid when ASYNC board is installed.
Where: xxx = ON or OFF.
Note: Only valid when ASYNC board is installed.
Where: xxxxx = RS232 or RS485.
Note: Only valid when ASYNC board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ASYNC board is installed.
Where: xxx = NRM or INV.
Note: Only valid when ASYNC board is installed.
SDM-100A Satellite Modem
Rev. 0
Advertisement
Table of Contents
