Operator Codes During Backup Diskette Generation Only - IBM 3270 Manual

Code
1
Meaning
Action
27 1. You specified languages 18 or 29 and they are not allowed with 1. Specify Portuguese ( 127=28).
your configuration support.
language
29
not allowed with
Configuration Support C.
2. You specified SFAP (162=1) and a language that is not allowed with
2. Verify and enter the correct responses.
SFAP
(121=02,08, 10, 13, 20, 26,
or
27).
3. You specified a language that is not allowed with a 3290 Information 3.
Verify and enter the correct response.
Panel (121=02, 06, 08, 09, 10, 12, 13, 20, 26, or 27).
28
Your responses to sequence numbers
113
(Extended Function Store) and Verify and enter the correct response.
151 (3274
Model Designation) are incompatible.
You have specified RTM (sequence number
127)
with a
3274
Model
1
A, -C, -D (sequence number 151). This is not allowed;
29 You specified an Attribute Select keyboard
(166=8
or C), but you did not Either change 166 to" A" or change 131
specify a Typewriter keyboard
(131=1)
or an APL keyboard
(132=1 ).
and/or 134 to "1".
30 1. You have specified a starting address for Multiple Interactive Screens Review instructions for defining Multiple
(sequence number 171), but you have not specified logical terminal
Interactive Screens (Appendix J) and enter
addresses.
the correct response.
2. You have specified logical terminal addresses for Multiple Interactive
Screens (sequence number
171),
but you have not specified a starting
address.
31 You have specified an invalid starting address for Multiple Interactive
Specify a starting address that is not port
Screens (sequence number 171 ).
AO, but is low enough to allow for your
required number of terminals.
32 Your response to either sequence number
112
or
171
is incorrect. You Review Appendix B, remembering that if
have specified more logical terminals than your system will allow. using BSC or a 3274 Model D, you cannot
specify more than 32 terminal addresses. If
using SDLC or 3274 Model A, you cannot
specify more than
128
terminal addresses.
33 Zero has been specified in sequence number 170, but you specified a
Either specify
1
to sequence number
170,
or
nonzero response to sequence number 171, 173, 175, or 176.
zeros to sequence numbers 171, 173, 175,
and
176.
36 You have specified a nonzero response for sequence number 139, but a Verify responses to sequence numbers 139
zero response for sequence number
170. 170
must be
1
for
139
to be and
170,
then enter the correct response(s).
nonzero.
60 Both response fields for sequence number
127
must be either zero Enter a zero or non-zero response in both
or non-zero. fields.
61 You do not have host support and your first digit response to sequence
Enter an acceptable response.
number
127
was a
3, 4,
or
5,
or your second digit was a
3.
This is not
allowed.
62 An invalid time boundary is specified in sequence number
128.
The Enter time values in the permitted range.
maximum time allowed is 27: 18.3. The seconds field must not exceed
59.
63 Field 81 in sequence number 128 cannot be specified as 00:00.0.
Specify at least
00:00.1
in field
81.
64 Entries for fields 81 through 84 in sequence number 128 are not in Enter boundary values in ascending order.
ascending order.
65 A time boundary value of
00:00.0
is embedded between two non-zero Enter an appropriate non-zero value.
values in sequence number
128.
This is not allowed.
66 A non-zero boundary value follows a max_imum boundary value Correct your boundary value sequence.
(27:18.3)
in sequence number
128.
Only a zero boundary value
(00:00.0)
can follow the maximum.
99 Your entries are acceptable, but the entry for sequence number 900, 901, Change the entry to a 1.
or
904
has not been changed to a
1 .
1
If any entry is unacceptable, the entry for sequence number 900 is changed back to 0 (zero) and the unacceptable
value is intensified. All codes except
99.
Figure 6-4 (Part 2 of 2). Operator Codes during Backup Diskette Generation Only
6-14