IBM 3270 Manual page 125

Code
1
Meaning
Action
27 1.
You specified languages 18 or 29 and they are not allowed with
1. Specify Portuguese (127=28).
your configuration support.
Language 29 not allowed with
Configuration Support C.
2. You specified SFAP (162=1) and a language that is not allowed with
2. Verify and enter the correct responses.
SFAP (121=02, 08, 10, 13, 20, 26, or 27).
3. You specified a language that is not allowed with a 3290 Information
3.
Verify and enter the correct response.
Panel (121=02, 06, 08, 09, 10, 12, 13, 20, 26, or 27).
28
Your responses to sequence numbers 113 (Extended Function Store) and
Verify and enter the correct response.
151 (3274 Model Designation) are incompatible.
You have specified RTM (sequence number 127) with a 3274 Model 1
A, -C, -D (sequence number 151). This is not allowed.
29 You specified an Attribute Select keyboard (166=8 or C), but you did not
Either change 166 to" A" or change 131
specify a Typewriter keyboard (131=1) or an APL keyboard (132=1 ).
and/or 134 to "1".
30 1. You have specified a starting address for Multiple Interactive Screens
Review instructions for defining Multiple
(sequence number 171), but you have not specified logical terminal
Interactive Screens (Appendix J) and enter
addresses.
the correct response.
2. You have specified logical terminal addresses for Multiple Interactive
Screens (sequence numbe.r 171 ), but you have not specified a starting
address.
31 You have specified an invalid starting address for Multiple Interactive
Specify a starting address that is not port
Screens (sequence number 171).
AO, but is low enough to allow for your
required number of terminals.
32 Your response to either sequence number 112 or 171 is incorrect. You
Review Appendix B, remembering that if
have specified more logical terminals than your system will allow.
using BSC or a 3274 Model D, you cannot
specify more than 32 terminal addresses. If
using SDLC or 3274 Model A, you cannot
specify more than 128 terminal addresses.
33 Zero has been specified in sequence number 170, but you specified a
Either specify 1 to sequence number 170, or
nonzero response to sequence number 171, 173, 175, or 176.
zeros to sequence numbers 171, 173, 175,
and 176.
36 You have specified a nonzero response for sequence number 139, but a
Verify responses to sequence numbers 139
zero response for sequence number 170. 170 must be 1 for 139 to be
and 170, then enter the correct response(s).
nonzero.
60 Both response fields for sequence number 127 must be either zero Enter a zero or non-zero response in both
or non-zero. fields.
61 You do not have host support and your first digit response to sequence Enter an acceptable response.
number 127 was a 3, 4, or 5, or your second digit was a 3. This is not
allowed.
62
An invalid time boundary is specified in sequence number 128. The
Enter time values in the permitted range.
maximum time allowed is 27:18.3. The seconds field must not exceed
59.
63
Field 81 in sequence number 128 cannot be specified as 00:00.0.
Specify at least 00:00.1 in field 81.
64 Entries for fields B 1 through 84 in sequence number 128 are not in Enter boundary values in ascending order.
ascending order.
65
A time boundary value of 00:00.0 is embedded between two non-zero Enter an appropriate non-zero value.
values in sequence number 128. This is not allowed.
66
A non-zero boundary value follows a maximum boundary value Correct your boundary value sequence.
(27:18.3) in sequence number 128. Only a zero boundary value (00:00.0)
can follow the maximum.
99
Your entries are acceptable, but the entry for sequence number 900, 901, Change the entry to a 1.
or 904 has not been changed to a 1 .
1
If any entry is unacceptable, the entry for sequence number 900 is changed back to 0 (zero) and the unacceptable
value is intensified. All codes except 99.
Figure 4-4 (Part 2 of 2). Operator Codes during Customizing Only
4-14