Beckhoff EPP3504-0023 Short Manual page 225

Text ID Type Place
0x8284 Error Communication Key loading failed
0x8285 Error Communication Reading Public Key failed: %X
0x8286 Error Communication Reading Public EK failed: %X
0x8287 Error Communication Reading PCR Value failed: %X
0x8288 Error Communication Reading Certificate EK failed: %X
0x8289 Error Communication Challenge could not be hashed:
0x828A Error Communication Tickstamp Process failed
0x828B Error Communication PCR Process failed: %X
0x828C Error Communication Quote Process failed: %X
0x82FF Error Communication Bootmode not activated
0x8300 Error Encoder
0x8301 Error Encoder
0x8302 Error Encoder
0x8303 Error Encoder
0x8304 Error Encoder
0x8305 Error Encoder
0x8306 Error Encoder
0x8307 Error Encoder
0x8308 Error Encoder
0x8309 Error Encoder
0x830A Error Encoder
0x830C Error Encoder
0x830D Error Encoder
0x8310 Error Encoder
0x8311 Error Encoder
0x8312 Error Encoder
0x8313 Error Encoder
0x8314 Error Encoder
0x8315 Error Encoder
0x8400 Error Drive
0x8401 Error Drive
0x8402 Error Drive
0x8403 Error Drive
0x8404 Error Drive
0x8405 Error Drive
0x8406 Error Drive
0x8407 Error Drive
0x8408 Error Drive
0x8409 Error Drive
EPP3504-0023
Text Message
%X
Set position error: 0x%X, %d
Encoder increments not
configured: 0x%X, %d
Encoder error
Encoder power missing (channel
%d)
Encoder communication error,
channel: %X
EnDat2.2 is not supported,
channel: %X
Delay time, tolerance limit
exceeded, 0x%X, channel: %X
Delay time, maximum value
exceeded, 0x%X, channel: %X
Unsupported ordering
designation, 0x%X, channel: %X
(only 02 and 22 is supported)
Encoder CRC error, channel: %X Encoder CRC error
Temperature %X could not be
read, channel: %X
Encoder Single-Cycle-Data Error,
channel. %X
Encoder Watchdog Error,
channel. %X
Initialisation error
Maximum frequency of the input
signal is exceeded (channel %d)
Encoder plausibility error
(channel %d)
Configuration error (channel %d)
Synchronisation error
Error status input (channel %d)
Incorrect drive configuration:
0x%X, %d
Limiting of calibration velocity:
%d, %d
Emergency stop activated: 0x%X,
%d
ADC Error
Overcurrent
Invalid modulo position: %d
DC-Link undervoltage (Error)
DC-Link overvoltage (Error)
I2T-Model Amplifier overload
(Error)
I2T-Model motor overload (Error)
Version: 1.2
Additional comment
Boot mode not activated
Error while setting the position
Encoder increments not configured
The amplitude of the resolver is too small
Encoder communication error
EnDat2.2 is not supported
Runtime measurement, tolerance exceeded
Runtime measurement, maximum value exceeded
Wrong EnDat order ID
Temperature cannot be read
CRC error detected. Check the transmission path and
the CRC polynomial
The sensor has not responded within a predefined time
period
Drive incorrectly configured
Limitation of the calibration velocity
Emergency stop activated
Error during current measurement in the ADC
Overcurrent in phase U, V or W
Modulo position invalid
The DC link voltage of the terminal is lower than the
parameterized minimum voltage. Activation of the
output stage is prevented.
The DC link voltage of the terminal is higher than the
parameterized maximum voltage. Activation of the
output stage is prevented.
• The amplifier is being operated outside the
specification.
• The I2T-model of the amplifier is incorrectly
parameterized.
• The motor is being operated outside the
parameterized rated values.
Appendix
225