Beckhoff EPP3504-0023 Short Manual page 222

Appendix
Text ID Type Place
0x1100 Information General
0x1135 Information General
0x1157 Information General
0x1158 Information General
0x1159 Information General
0x117F Information General
0x1201 Information Communication Communication re-established
0x1300 Information Encoder
0x1303 Information Encoder
0x1304 Information Encoder
0x1305 Information Encoder
0x1400 Information Drive
0x1401 Information Drive
0x1705 Information
0x1706 Information
0x1707 Information
0x170A Information
0x170C Information
0x170D Information
Text ID Type Place
0x2000 Information System
0x2001 Information System
0x2002 Information System
0x2003 Information System
0x2004 Information System
0x2005 Information System
0x2006 Information System
0x2007 Information System
0x2008 Information System
0x2009 Information System
Text ID Type Place
0x4000 Warning
0x4001 Warning System
0x4002 Warning System
0x4003 Warning System
0x4004 Warning System
222
Text Message
Detection of operation mode
completed: 0x%X, %d
Cycle time o.k.: %d
Data manually saved (Idx: 0x%X,
SubIdx: 0x%X)
Data automatically saved (Idx:
0x%X, SubIdx: 0x%X)
Data deleted (Idx: 0x%X, SubIdx:
0x%X)
Information: 0x%X, 0x%X, 0x%X Information
Position set: %d, %d
Encoder Supply ok
Encoder initialization
successfully, channel: %X
Sent command encoder reset,
channel: %X
Drive is calibrated: %d, %d
Actual drive state: 0x%X, %d
CPU usage returns in normal
range (< 85%%)
Channel is not in saturation
anymore
Channel is not in overload
anymore
No channel range error anymore A measuring range error is no longer active
Calibration data saved
Calibration data will be applied
and saved after sending the
command "0x5AFE"
Text Message
%s: %s
%s: Network link lost
%s: Network link detected
%s: no valid IP Configuration -
Dhcp client started
%s: valid IP Configuration (IP:
%d.%d.%d.%d) assigned by
Dhcp server %d.%d.%d.%d
%s: Dhcp client timed out
%s: Duplicate IP Address
detected (%d.%d.%d.%d)
%s: UDP handler initialized
%s: TCP handler initialized
%s: No more free TCP sockets
available
Text Message
Warning: 0x%X, 0x%X, 0x%X
Warning: 0x%X, 0x%X, 0x%X
%s: %s Connection Open (IN:%d
OUT:%d API:%dms) from %d.
%d.%d.%d successful
%s: %s Connection Close (IN:%d
OUT:%d) from %d.%d.%d.%d
successful
%s: %s Connection (IN:%d OUT:
%d) with %d.%d.%d.%d timed
out
Version: 1.2
Additional comment
Detection of the mode of operation ended
Cycle time OK
Data saved manually
Data saved automatically
Data deleted
Communication to the field side restored
This message appears, for example, if the voltage was
removed from the power contacts and re-applied during
operation.
Position set - StartInputhandler
Encoder power supply unit OK
Encoder initialization successfully completed
Send encoder reset command
Drive is calibrated
Current drive status
Processor load is back in the normal range
Channel is no longer in saturation
Channel is no longer overloaded
Calibration data were saved
Calibration data are not applied and saved until the
command "0x5AFE" is sent.
Additional comment
Network connection lost
Network connection found
Invalid IP configuration
Valid IP configuration, assigned by the DHCP server
DHCP client timeout
Duplicate IP address found
UDP handler initialized
TCP handler initialized
No free TCP sockets available.
Additional comment
General warning; parameters depend on event. See
device documentation for interpretation.
EPP3504-0023