Roland VersaUV LEF2-200 Service Notes page 144

Service mode
PRINT MENU
FLUSHING ADJ.
PRINT MENU
MARKER POS ADJ.
PRINT MENU
PRINT AREA ADJ.
SERVICE MENU
I/S MENU
NOW PROCESSING.. FLUSHING ADJ.
0.00mm>-0.40mm
Flushing position adjustment
This is for adjusting the ushing position.As entering the menu, the head carriage moves to the current ushing position.
With [left] and [right] keys, move the cap tops and heads to the position where the cap case guide makes contact
with the carriage cap guide, and press [ENTER] key to save the position. As [ENTER] key is pressed,
the head is automatically capped and it backs out the menu. For backing out the menu without saving the position,
press [MENU] key without pressing [ENTER] key.
NOW PROCESSING.. PERFORMING
TEST PRINT
Base point marker position adjustment
This is for adjusting the LED pointer position. As entering the menu, the head carriage moves to above the test pattern after the test print.
When it shows [****], it means that it has never been setup. With [left] and [right] keys, move the head carriage to the positionwhere the laser
pointer points the centermost square of the test pattern and press [ENTER] key to save the position. As [ENTER] key is pressed, the head is
automatically capped and it backs out the menu. For backing out the menu without saving the position, press [MENU] key without pressing
[ENTER] key.
Range: -5.0 mm to 5.0 mm Default: 0.0 mm
NOW PROCESSING.. S:****>+0.1mm
F:****>-0.3mm
This is for adjusting the printing area and engraved line of the table.
As entering the menu, the head carriage moves to above the table.
When it shows [****], it means that it has never been setup. With [left] and [right] keys, move the head carriage to the position
where the laser pointer point lower right of the engraved line after of the test pattern and press [ENTER] key to save the position.
As [ENTER] key is pressed, the head is automatically capped and it backs out the menu.
For backing out the menu without saving the position, press [MENU] key without pressing [ENTER] key.
NOW PROCESSING..
I/S MENU
I/S CHECK
Checking
Ink system check
This menu is for checking the motors and sensors of cap (Up/Down), wipers and slider.
**Make sure to move the head carriage towards left o the capping unit before performing this check. Otherwise,
it may damage head, cap or wiper unit.
Error Displays CAP: Error is found on capping motor or capping sensor.
WIPER: Error is found on wiper motor or wiper sensor.
I/S MENU PUMP CHECK
PUMP CHECK PUMP SUCTION
PUMP CHECK
PUMP RELEASE
Pump motor check
This is for checking the pump motor. The rotation for both ink suction and release can be
checked.All pump motors rotate for 5 seconds and stop.
I/S MENU I/S CONTROL
I/S CONTROL WIPER
Wiper check
WIPER: Move the wiper towards front and rear.
Option: FRONT/REAR Default: FRONT
**Caution: When moving the head carriage by hand, pay attention to the cap height and wiper position
to avoid clashing. Also, when moving the cap and wiper, pay attention to the carriages,
especially to the head carriage.
REFRESHER ADJ.
I/S MENU
DEFAULT
REFRESHER ADJ.
Head refresher height adjustment
This is for adjusting the height of head refresher.When ADJUST is selected, the machine
automatically detects the height.The adjustment fails if the table height cannot be
adjusted between 60 mm to 4 mm during automatical adjustment.
When adjustment failed, the height is set to DEFAULT.
Range ： DEFAULT/ADJUST Default ： DEFAULT
2-3
NOW PROCESSING..
NOW PROCESSING..
S:****>+0.1mm
F:****>-0.3mm
NOW PROCESSING..
Normal
I/S CHECK
COMPLETED
Error
I/S CHECK ERROR
WIPER
NOW PROCESSING..
PUMP SUCTION
AB
PUMP SUCTION
NOW PROCESSING..
CIR-PUMP
PUMP RELEASE NOW PROCESSING..
AB
PUMP RELEASE NOW PROCESSING..
CIR-PUMP
WIPER
FRONT
NOW PROCESSING..
SET HEAD
REFRESHER
NOW PROCESSING..
ADJUST
COMPLETED
ADJUST FAILED
2
Normal
Error
L EF 2-200