Setting A Skip Channel - Icom IC-V3500 Advanced Manual

SCAN OPERATION
4.

Setting a Skip channel

You can set or clear a Skip channel� The Memory channels set as a Skip channel are skipped during a scan�
1� Repeatedly push [M/CALL PRIO] to select the
Memory mode and rotate [DIAL] to select a
Memory channel�
2� Push [SET LOCK] to enter the Set mode�
L You cannot enter the Set mode when the Channel
Name Display mode is selected� To exit this mode,
hold down [MONI ANM PA] for 1 second, and then do
step 2� See page 3-8 for details�
L When "NM" is selected in "DSP" (Display type) in the
Initial Set mode, you can enter the Set mode, even if
the channel name is displayed� (p� 8-6)
3� Repeatedly push [SET LOCK] or [MONI ANM PA]
to select "CHS" (Channel skip setting)�
4� Rotate [DIAL] to select "ON�"
• " " is displayed�
L To clear a Skip channel, select "OF�"
5� Push any key other than [SET LOCK] or
[MONI ANM PA] to save and exit the Set mode�
Using the HM-133V microphone
1� Push [MR/CALL] to select the Memory mode and
push [▲] or [▼] to select a Memory channel.
2� Push [SET B D-OFF] to enter the Set mode�
L You cannot enter the Set mode when the Channel
Name Display mode is selected� To exit this mode,
push [FUNC], and then [MONI 1 ANM], and then do
step 2� See page 3-8 for details�
L When "NM" is selected in "DSP" (Display type) in the
Initial Set mode, you can enter the Set mode, even if
the channel name is displayed� (p� 8-6)
3� Push [SET B D-OFF] or [ENT C T-OFF] to select
"CHS" (Channel skip setting)�
4� Push [▲] to select "ON."
• " " is displayed�
L To clear a Skip channel, push [▼] to select "OF."
5� Push [CLR A MW] to save and exit the Set mode�
Example: Setting Memory channel 20 as a Skip
channel.
Select Memory channel 20�
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET MONI LOW TONE
Push [SET LOCK] to enter the Set mode�
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
Push [SET LOCK] or [MONI ANM] to select "CHS�"
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET MONI LOW TONE
Rotate [DIAL] to select "ON�"
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET
MONI LOW TONE
Example: Setting Memory channel 20 as a Skip
channel.
Select Memory channel 20�
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET MONI LOW TONE
Push to enter the Set mode�
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
Push or to select "CHS�"
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET MONI LOW TONE
Push to select "ON�"
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN
S ET MONI LOW TONE
4-11
PRIO SCAN
M/CALL V/ MHz
PRIO SCAN
M/CALL V/ MHz
" " is displayed�
PRIO SCAN
M/CALL V/ MHz
PRIO SCAN
M/CALL V/MHz
PRIO SCAN
M/CALL V/MHz
" " is displayed�
PRIO SCAN
M/CALL V/MHz