Icom IC-V3500 Advanced Manual page 70

SET MODES
8.
Initial Set mode items
Squelch type
Selects the squelch type�
• OF: Noise squelch�
• SS: S-meter squelch�
The S-meter Squelch function disables the
audio output from the speaker when the
received signal is weaker than the specified
S-meter squelch level�
To turn ON the function, rotate [SQL]
clockwise to a point past the 12 o'clock
position�
• AT: Squelch attenuator�
Approximately 20 dB of attenuation is
obtained at the maximum setting�
To turn ON the function, rotate [SQL]
clockwise to a point past the 12 o'clock
position�
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
Tone burst
Turns the Tone Burst function ON or OFF�
• OF: When you transmit a signal that superimposes
a CTCSS tone, the other station may hear a
short burst of noise from their receiver just after
you stop transmitting�
• ON: When you transmit a signal that superimposes
a CTCSS tone, the function mutes the noise
from being heard in the other station's receiver�
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET
MONI
DTMF speed
Selects the DTMF transmit speed�
• 1: Transmits the DTMF codes at about 100
milliseconds per code (5 characters per second)�
• 2: Transmits the DTMF codes at about 200
milliseconds per code (2�5 characters per second)�
• 3: Transmits the DTMF codes at about 300
milliseconds per code (1�6 characters per second)�
• 5: Transmits the DTMF codes at about 500
milliseconds per code (1 character per second)�
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: OF)
AO
(Default: OF)
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: 1)
AO
Display type
Selects the display type of the Memory mode�
• FR: The entered frequency is displayed�
• CH: The Memory Channel number is displayed�
• NM: The channel name is displayed�
L When "CH" is selected, the usable functions and Set
mode items will be restricted as shown below�
Usable functions when "CH" is selected:
• Memory scan
• Selecting an output power
• Adjusting the volume or squelch level
• Monitor function
• Lock function
• Set mode
(Settable items are "SCP" (Scan Stop timer), "SCT"
(Scan Resume timer), "DIM" (Display dimmer), "ATD"
(Auto dimmer), "CON" (Display contrast), "BLK" (Bank
Link function), and "MIC" (MIC gain)�)
MUTE
NAR
MID
LOW
LOCK
S ET
Voltage display
Selects whether or not to display the power source
voltage�
• OF: The supplied voltage is not displayed�
• ON: When the transceiver is turned ON, the
supplied voltage is displayed�
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
[BANK/OPT] key
Assigns the function to [BANK/OPT]�
• BAK: The Memory Bank mode and the Option Set
mode are assigned�
When the Memory mode is selected, push
[BANK/OPT] to enter the Memory Bank mode�
Hold down [BANK/OPT] for 1 second to enter
the Option Set mode�
• EMR: The Emergency Call function is assigned�
Hold down [BANK/OPT] for 3 second to turn
ON the function�
• TVo: The Temporary Volume function and the
Option Set mode are assigned�
Push [BANK/OPT] to change the volume
level to the value set in the Temporary volume
setting�
Hold down [BANK/OPT] for 1 second to enter
the Option Set mode�
NAR
MID
LOW
S ET
8-6
(Default: FR)
AO
ANM
MONI
(Default: ON)
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: BAK)
AO
ANM
MONI
AO