Using The Initial Set Mode; Initial Set Mode Items - Icom IC-V3500 Advanced Manual

SET MODES
8.

Using the Initial Set mode

The initial Set mode can be accessed when the
transceiver is turned ON, and allows you to set
seldom-changed settings� In this way, you can
"customize" the transceiver to suit your preference
and operating style�

Initial Set mode items

NOTE: The default settings may differ, depending on
the transceiver version�
Key-touch beep
Turns the confirmation beeps ON or OFF�
• OF: No beep sounds�
• ON: A beep sounds when a key is pushed�
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET
MONI
Time-out timer
To prevent an accidental prolonged transmission,
the transceiver has a Time-out Timer function� The
function inhibits continuous transmissions longer than
this set period of time�
• OF: Turns OFF the function�
• 1 ~ 30: Transmission is cut OFF after the set period
of time ends (1 to 30 minutes)�
Approximately 10 seconds before the Time-out timer
is activated, the transceiver sounds a beep tone as a
warning�
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
Auto Repeater
The Auto Repeater function automatically turns the
duplex settings and the tone encoder ON or OFF�
L This item is displayed in only the USA version�
L The frequency offset and the Repeater Tone frequency
are not changed by this function� Reset these
frequencies, if necessary�
• OF: Turns OFF the function�
• R1: Turns ON the duplex settings only�
• R2: Turns ON the duplex settings and the tone
encoder�
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: ON)
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: OF)
AO
(Default: R1)
DIGITAL PRIO AO BUSY
DUP T-SCAN PRIO SCAN
LOW TONE M/CALL V/MHz
1� While holding down [SET LOCK], hold down [ ]
for 1 second to enter the Initial Set mode�
2� Repeatedly push [SET LOCK] or [MONI ANM PA]
to select the desired item�
3� Rotate [DIAL] to select an option or value�
4� Push [ ] to save and exit the Initial Set mode�
Auto Power OFF
Selects whether or not to automatically turn OFF the
transceiver after inactivity for this set period of time�
L When the function is ON, "AO" is displayed in the function
display�
L Beeps sound when turning OFF the transceiver� If you
operate the transceiver during this period of time, the
Auto Power OFF timer is reset�
• OF:
AO
• 30/1H/2H: Turns OFF the transceiver after inactivity
Repeater Lockout
Sets the transmit lockout (temporary transmission
inhibit) capability�
• OF: Turns OFF the function�
• RP: Transmit capability is inhibited when a
signal with an unmatched subaudible tone is
received�
• BU: Transmit capability is inhibited when a signal
is received�
Squelch delay
Sets the squelch delay to short or long� The delay
prevents the squelch from repeatedly opening and
closing when receiving the same signal�
• S: Short squelch delay�
• L: Long squelch delay�
8-5
Does not turn OFF the transceiver�
for this set period of time (30 minutes,
1 hour, or 2 hours)�
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET
MONI
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
AO
MUTE
NAR
MID
LOW
LOCK ANM
S ET MONI
(Default: OF)
(Default: OF)
(Default: S)