Honda NC700 2012 Service Manual page 547

dummyhead dummyhead
ENGINE REMOVAL/INSTALLATION
SERVICE INFORMATION
GENERAL
• A hoist or equivalent is required to support the motorcycle when removing and installing the engine.
• When removing/installing the engine, tape the frame around the engine beforehand for frame protection.
• When installing the engine, be sure to tighten the engine mounting fasteners to the specified torque in the specified sequence. If
you mistake the torque or sequence, loosen all mounting fasteners, then tighten them again to the specified torque in the correct
sequence.
• The following components can be serviced with the engine installed in the frame.
– Starter motor (page 6-8)
– Throttle body (page 7-15)
– Water pump (page 8-12)
– Oil pump (NC700X/XA/S/SA) (page 9-6)
– Oil pump (NC700XD/SD) (page 9-8)
– Rocker arm (page 10-8)
– Clutch (NC700X/XA/S/SA) (page 11-7)
– Gearshift linkage (NC700X/XA/S/SA) (page 11-16)
– Primary drive gear/CKP sensor rotor (NC700X/XA/S/SA) (page 11-15)
– Dual clutch (NC700XD/SD) (page 12-105)
– Gearshift linkage (NC700XD/SD) (page 12-112)
– Primary drive gear/CKP sensor rotor (NC700XD/SD) (page 12-108)
– CKP sensor (page 5-11)
– Flywheel (page 13-7)
– Stator (page 13-13)
• The following components require engine removal for service.
– Camshaft (page 10-13)
– Cylinder head/valves (page 10-16)
– Transmission (NC700X/XA/S/SA) (page 14-8)
– Transmission (NC700XD/SD) (page 14-17)
– Balancer (page 14-26)
– Crankshaft (page 15-5)
– Piston/cylinder (page 15-14)
SPECIFICATIONS
Engine dry NC700X/XA/S/SA
weight
NC700XD/SD
Engine oil NC700X/XA/S/SA
capacity
NC700XD/SD
Coolant Radiator and engine
capacity
At draining
Reserve tank
TORQUE VALUES
ITEM
Rear lower engine hunger nut
Front lower engine hunger bolt
Upper engine hunger bolt
Rear upper engine hunger nut
Step holder mounting socket bolt
Drive sprocket bolt
Starter motor terminal nut
Water hose band screw
16-4
ITEM
After draining
After draining/filter
change
After disassembly
After draining
After draining/filter
change
After disassembly
THREAD
Q'TY
DIA. (mm)
1 12
2 12
2 12
1 12
4 8
1 10
1 6
2 –
SPECIFICATIONS
60.5 kg (133.4 lbs)
67.3 kg (148.4 lbs)
3.1 liters (3.3 US qt, 2.7 Imp qt)
3.4 liters (3.6 US qt, 3.0 Imp qt)
3.7 liters (3.9 US qt, 3.3 Imp qt)
3.2 liters (3.4 US qt, 2.8 Imp qt)
3.4 liters (3.6 US qt, 3.0 Imp qt)
4.1 liters (4.3 US qt, 3.6 Imp qt)
1.69 liters (1.79 US qt, 1.49 Imp qt)
1.41 liters (1.49 US qt, 1.24 Imp qt)
0.13 liter (0.14 US qt, 0.11 Imp qt)
TORQUE
N·m (kgf·m, lbf·ft)
59 (6.0, 44)
54 (5.5, 40)
54 (5.5, 40)
54 (5.5, 40)
32 (3.3, 24)
54 (5.5, 40)
10 (1.0, 7)
– See page 16-18
See page 16-19
See page 16-24
See page 16-25
REMARKS