Table of Contents
Advertisement
[LAST MEMORY]
[STANDBY]
[ON]
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
Press as to select [STARTUP INPUT SELECT].
1)
2)
Press the <ENTER> button.
f The [STARTUP INPUT SELECT] screen is displayed.
Press asqw to select the input, and press the <ENTER> button.
3)
[LAST USED]
[HDMI]
[DIGITAL LINK]
[HDMI1 [SLOT1]]
[HDMI2 [SLOT1]]
[HDMI3 [SLOT2]]
[HDMI4 [SLOT2]]
[DVI-D1 [SLOT1]]
[DVI-D2 [SLOT1]]
[DVI-D3 [SLOT2]]
[DVI-D4 [SLOT2]]
[DisplayPort1 [SLOT1]]
[DisplayPort2 [SLOT1]]
[DisplayPort3 [SLOT2]]
[DisplayPort4 [SLOT2]]
[SDI1 [SLOT1]]
*1
[SDI2 [SLOT1]]
*1
[SDI3 [SLOT1]]
*3
[SDI4 [SLOT1]]
*3
[SDI1 [SLOT2]]
*3
[SDI2 [SLOT2]]
*3
[SDI3 [SLOT2]]
*2
[SDI4 [SLOT2]]
*2
[SDI OPT1 [SLOT1]]
[SDI OPT2 [SLOT1]]
[SDI OPT1 [SLOT2]]
[SDI OPT2 [SLOT2]]
[INPUT1] - [INPUT10]
*1 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 1>.
*2 This can be selected when the optional Interface Board equipped with corresponding input is installed in <SLOT 2>.
*3 This is displayed when the optional Interface Board for 12G-SDI (Model No.: ET-MDN12G10) is installed in <SLOT 1> or <SLOT 2>.
*4 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the projector, its input
name is automatically reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
[DATE AND TIME]
Set the time zone, date, and time of the built-in clock of the projector.
Setting the time zone
Press as to select [DATE AND TIME].
1)
2)
Press the <ENTER> button.
f The [DATE AND TIME] screen is displayed.
Press as to select [TIME ZONE].
3)
Chapter 4 Settings — [PROJECTOR SETUP] menu
Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
Starts up the projector in standby.
Starts projecting immediately.
Keeps the input selected last.
Sets the input to HDMI.
Sets the input to DIGITAL LINK.
Sets the input to HDMI1 of the Interface Board.
*1
Sets the input to HDMI2 of the Interface Board.
*1
Sets the input to HDMI3 of the Interface Board.
*2
Sets the input to HDMI4 of the Interface Board.
*2
Sets the input to DVI-D1 of the Interface Board.
*1
Sets the input to DVI-D2 of the Interface Board.
*1
Sets the input to DVI-D3 of the Interface Board.
*2
Sets the input to DVI-D4 of the Interface Board.
*2
Sets the input to DisplayPort1 of the Interface Board.
*1
Sets the input to DisplayPort2 of the Interface Board.
*1
Sets the input to DisplayPort3 of the Interface Board.
*2
Sets the input to DisplayPort4 of the Interface Board.
*2
Sets the input to SDI1 of the Interface Board.
Sets the input to SDI2 of the Interface Board.
Sets the input to SDI3 of the Interface Board.
Sets the input to SDI4 of the Interface Board.
Sets the input to SDI1 of the Interface Board.
Sets the input to SDI2 of the Interface Board.
Sets the input to SDI3 of the Interface Board.
Sets the input to SDI4 of the Interface Board.
Sets the input to SDI OPT1 of the Interface Board.
*1
Sets the input to SDI OPT2 of the Interface Board.
*1
Sets the input to SDI OPT1 of the Interface Board.
*2
Sets the input to SDI OPT2 of the Interface Board.
*2
Sets the input to DIGITAL LINK, and switches the input of the Panasonic twisted-pair-cable
*4
transmitter to the specified input.
ENGLISH - 189
Advertisement
Table of Contents
