Table of Contents
Advertisement
[NO SIGNAL SHUT-OFF]
A function that automatically switches the power source of the projector to standby if there is no input signal for a
certain period of time. The time before switching to standby can be set.
1)
Press as to select [NO SIGNAL SETTING].
2)
Press the <ENTER> button.
f The [NO SIGNAL SETTING] screen is displayed.
3)
Press as to select [NO SIGNAL SHUT-OFF].
4)
Press qw to switch the item.
f The items will switch each time you press the button.
[DISABLE]
[10MIN.] - [90MIN.]
Note
f The [NO SIGNAL SHUT-OFF] setting item is common with the following menu item.
g The [PROJECTOR SETUP] menu → [POWER MANAGEMENT] → [NO SIGNAL SHUT-OFF]
[INITIAL STARTUP]
Set the startup method when the <MAIN POWER> switch is set to <ON>.
1)
Press as to select [INITIAL STARTUP].
2)
Press qw to switch the item.
f The items will switch each time you press the button.
[LAST MEMORY]
[STANDBY]
[ON]
[STARTUP INPUT SELECT]
Set the input when the projector is switched on to start projection.
1)
Press as to select [STARTUP INPUT SELECT].
2)
Press the <ENTER> button.
f The [STARTUP INPUT SELECT] screen is displayed.
3)
Press asqw to select the input, and press the <ENTER> button.
[LAST USED]
[HDMI1]
[HDMI2]
[DisplayPort]
[SDI [SLOT]]
*1
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
[DIGITAL LINK [SLOT]]
[PressIT [SLOT]]
[SLOT]
*5
[INPUT1] - [INPUT10]
*1 This item can be selected when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
*2 This item can be selected when the optional Function Board for 12G-SDI Optical (Model No.: TY-SB01FB) is installed in <SLOT>.
*3 This item can be selected when the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) is installed in <SLOT>.
*4 This item can be selected when the optional Wireless Presentation System Receiver Board (Model No.: TY-SB01WP) is installed in <SLOT>.
*5 This item can be selected when the Function Board by other manufacturers is installed in <SLOT>.
*6 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK IN/
LAN> terminal of the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) installed in <SLOT>, its input name is automatically
reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
174 - ENGLISH
Chapter 4 Settings — [PROJECTOR SETUP] menu
Disables the No signal shut‑off function.
Sets the time in increments of 10 minutes.
Starts up the projector in the condition before the <MAIN POWER> switch is set to <OFF>.
Starts up the projector in standby.
Starts projecting immediately.
Keeps the input selected last.
Sets the input to HDMI1.
Sets the input to HDMI2.
Sets the input to DisplayPort.
Sets the input to SDI.
Sets the input to SDI OPT1.
*2
Sets the input to SDI OPT2.
*2
Sets the input to DIGITAL LINK.
*3
Sets the input to PressIT.
*4
Sets the input to SLOT.
Sets the input to DIGITAL LINK, and switches the input of the DIGITAL LINK output supported device
*3 *6
to the specified input.
Advertisement
Table of Contents
