Table of Contents
Advertisement
g Input the same signal to the primary and secondary inputs.
g Display the image of the primary input or secondary input.
f If the input is switched to other than the primary or secondary input while the backup function is ready for use, the state of readiness to
use the backup function is canceled. To switch to the backup input signal using the backup function again, switch to the primary input or
secondary input.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the combination of that input is displayed in [PRIMARY INPUT] and
[SECONDARY INPUT] of the [BACKUP INPUT SETTING] screen.
f [BACKUP INPUT STATUS] is displayed in the input guide (x page 158) and the [STATUS] screen (x pages 97, 197) when [BACKUP
INPUT MODE] is set to anything other than [OFF].
When the signal can be switched to the backup input signal using the backup function, [ACTIVE] is displayed in [BACKUP INPUT STATUS].
When it is not possible, [INACTIVE] is displayed instead.
The secondary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the primary
input is displayed.
The primary input will be the backup input when [BACKUP INPUT STATUS] is displaying [ACTIVE] while the image from the secondary
input is displayed.
f When [BACKUP INPUT MODE] is set to anything other than [OFF], the input is switched seamlessly if the input is switched between the
primary input and the secondary input while it is possible to switch to the backup input signal.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], and [BACKUP INPUT STATUS] shows [ACTIVE], the signal is switched to the
backup input if a disruption occurs in the input signal.
f When [AUTOMATIC SWITCHING] is set to [ENABLE], the indication in [BACKUP INPUT STATUS] will change to [INACTIVE] if the input
signal is disrupted and automatically switched to the backup input. In this case, it is not possible to switch to the backup input signal until the
original input signal is restored. If the input has switched to the backup input automatically, it is possible to switch to the backup input signal
when the original signal has restored. In this case, the current input is maintained.
f [BACKUP INPUT MODE] in which the input equipped on the optional Interface Board installed in the slot is included as the primary input or
the secondary input cannot be selected when the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] → [AUTO(x2-speed)] is set.
f When [SDI LINK] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT MODE] for that combination cannot
be selected. When [SDI LINK] for the primary input and the secondary input do not match, [BACKUP INPUT MODE] for that combination
cannot be selected.
Match the setting in accordance with the signal and then input the same signal in the primary input and the secondary input.
g The [DISPLAY OPTION] menu → [SLOT IN] → [SDI LINK]
f When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the secondary input is set to [AUTO], [BACKUP INPUT
MODE] for that combination cannot be selected. When [HDMI LINK SETTINGS] or [DVI-D LINK SETTINGS] for the primary input and the
secondary input do not match, [BACKUP INPUT MODE] for that combination cannot be selected.
Match the setting in accordance with the signal and then input the same signal in the primary input and the secondary input.
g The [DISPLAY OPTION] menu → [SLOT IN] → [HDMI LINK]
g The [DISPLAY OPTION] menu → [SLOT IN] → [DVI-D LINK]
f The primary input setting values are applied to image adjustment values such as the [PICTURE] menu → [PICTURE MODE], [GAMMA],
and [COLOR TEMPERATURE].
[SIMUL INPUT SETTING]
Set this function when the video signal in simultaneous format is input and used.
This can be set when the same optional Interface Board supporting the simultaneous input is installed in both of
the slots.
Press as to select [SIMUL INPUT SETTING].
1)
2)
Press the <ENTER> button.
f The [SIMUL INPUT SETTING] screen is displayed.
Press qw to switch the setting.
3)
f The items will switch each time you press the button.
[OFF]
[AUTO(x2-speed)]
Note
f [SIMUL INPUT SETTING] can be set when the main version of the firmware is 1.07 or higher. [SIMUL INPUT SETTING] will be able to be
set by updating the firmware if the main version is lower than 1.07.
Check the Panasonic website (https://panasonic.net/cns/projector/pass/) for availability of the firmware that can be updated. For details on
how to update the firmware, refer to "Updating the firmware" (x page 277).
f The image for double speed is displayed when [AUTO(x2-speed)] is set and the same corresponding signal is input to each of the input
terminal.
f [SIMUL INPUT SETTING] including the input set as the primary input or the secondary input is fixed to [OFF] when the [PROJECTOR
SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set to anything other than [OFF].
f [SIMUL INPUT SETTING] is fixed to [OFF] when [HDMI LINK], [DVI-D LINK], or [SDI LINK] in [SLOT IN] is set to anything other than
[SINGLE].
Chapter 4 Settings — [DISPLAY OPTION] menu
This is not used for simultaneous input.
Displays the image in double speed using the signals input in the two input terminals.
ENGLISH - 135
Advertisement
Table of Contents
