Table of Contents
Advertisement
Press as to select [SDI MODE].
3)
Press qw to switch the item.
4)
f The items will switch each time you press the button.
[INPUT]
[OUTPUT]
Note
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal do not support the input of the 6G-SDI signal or the 12G-SDI signal.
f The <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal support the output of the HD-SDI signal, 3G-SDI signal, 6G-SDI signal,
and 12G-SDI signal.
f When the projector is in standby mode, a signal is not output from the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal.
Setting [SDI LINK] in [SLOT IN] (SDI input)
Press as to select [SLOT IN].
1)
2)
Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
Press as to select [SDI LINK], and press the <ENTER> button.
3)
f The [SDI LINK] screen is displayed.
Press as to select the setting.
4)
[AUTO]
[SINGLE]
[DUAL]
[QUAD]
5)
Press the <ENTER> button.
Note
f The single link is a setting to display one image with one input signal. The dual link is a setting to display one image with two input signals.
The quad link is a setting to display one image with four input signals.
f [SDI LINK] is fixed to [SINGLE] in the following cases.
g When the [DISPLAY OPTION] menu → [SIMUL INPUT SETTING] is set to [AUTO(x2-speed)]
f When the [PROJECTOR SETUP] menu → [NO SIGNAL SETTING] → [BACKUP INPUT SETTING] → [BACKUP INPUT MODE] is set as
the combination to use the SDI input, the [SDI LINK] setting cannot be changed.
f When [SDI LINK] is set to [AUTO], use the same format for the signal to be input to the <SDI 1 IN>/<SDI 2 IN/1 OUT>/<SDI 3 IN>/<SDI 4
IN/3 OUT> terminals. If different format signal is input to even one terminal, currently displayed image may not be projected correctly.
f [SDI MAPPING] and [3G-SDI MAPPING] cannot be set when [SDI LINK] is set to [AUTO].
f The content set is displayed in [SDI LINK SETTINGS].
Setting [RESOLUTION] in [SLOT IN] (SDI input)
Press as to select [SLOT IN].
1)
2)
Press the <ENTER> button.
f The [SLOT IN] screen is displayed.
Press as to select [SINGLE LINK SETTING], [DUAL LINK SETTING], or [QUAD LINK SETTING], and
3)
press the <ENTER> button.
f The [SINGLE LINK SETTING] screen, the [DUAL LINK SETTING] screen, or the [QUAD LINK SETTING]
screen is displayed.
f Proceed to Step 5) when [DUAL LINK SETTING] or [QUAD LINK SETTING] is selected.
Chapter 4 Settings — [DISPLAY OPTION] menu
Select this item when using the <SDI 2 IN/1 OUT> terminal and the <SDI 4 IN/3 OUT> terminal as
SDI2 input and SDI4 input.
Select this item when the signal input to the <SDI 1 IN> terminal is output from the <SDI 2 IN/1
OUT> terminal, and the signal input to the <SDI 3 IN> terminal is output from the <SDI 4 IN/3 OUT>
terminal.
Automatically selects the single link, the dual link, or the quad link.
Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input of the Interface Board to
single link.
(Factory default setting)
Sets the SDI1 input and the SDI3 input of the Interface Board to dual link.
Sets the SDI1 input, the SDI2 input, the SDI3 input, and the SDI4 input of the Interface Board to quad
link.
ENGLISH - 151
Advertisement
Table of Contents
