Table of Contents
Advertisement
Acoustic noise
*1
Operating temperature
Operating
environment
Operating humidity
Operation position
Power requirements
Maximum power consumption
Standby mode power consumption
Width
Standard outside
Height
dimensions
Depth
Weight
*5
Materials
Outer case
Color
Power cord length
Laser Class
Laser
Classification
Risk Group
Compliance standards
Transmission method
Frequency range
(Channel)
Wireless LAN
*6
Data transfer speed
(Standard value)
Encryption method
Power requirements
Operating range
Remote control
Weight
Outside dimensions
*1 Measurement, measuring conditions, and method of notation all comply with ISO/IEC 21118:2020 international standards.
*2 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) if the projector is used at an altitude between 1 400 m
(4 593') and 4 200 m (13 780') above sea level.
*3 The operating environment temperature should be between 0 °C (32 °F) and 40 °C (104 °F) when the optional Wireless Module (Model No.:
AJ-WM50 Series) is attached.
*4 When the [PROJECTOR SETUP] menu → [OPERATION SETTING] → [OPERATING MODE] is set to [NORMAL] or [ECO], and the operating
environment temperature exceeds the following value, the light output may be reduced to protect the projector.
f When using the projector at an altitude lower than 2 700 m (8 858') above sea level: 35 °C (95 °F)
f When using the projector at an altitude between 2 700 m (8 858') and 4 200 m (13 780') above sea level: 25 °C (77 °F)
*5 Average value. Weight varies for each product.
*6 To use the wireless LAN function with the projector, it is necessary to attach the optional Wireless Module (Model No.: AJ-WM50 Series).
Note
f The light output will decrease to approximately 1/3 when using the projector with AC 100 V to AC 120 V.
f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI
2 input (Model No.: ET-MDNHM10), it is necessary for the firmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the
version is earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding
the version update to the latest firmware.
For details on how to confirm the firmware version, refer to "How to confirm the firmware version of the Interface Board (optional)"
(x page 38).
f The model numbers of accessories and optional accessories are subject to change without prior notice.
Chapter 7 Appendix — Specifications
49 dB
49 dB
46 dB
0 °C (32 °F) to 45 °C (113 °F)
10 % to 80 % (no condensation)
[FLOOR/CEILING], [FRONT/REAR]
100 V - 120 V / 200 V - 240 V ~ (100 V - 120 V / 200 V - 240 V alternating current),
50 Hz/60 Hz
1 150 W / 2 550 W
14 W
598 mm (23-17/32") (excluding protrusions)
402 mm (15-13/16") (with the feet at shortest position, including protrusions)
353 mm (13-29/32") (excluding the feet and protrusions)
780 mm (30-23/32") (excluding protrusions)
Approx. 69.8 k] (154 lbs.)
Molded plastic
Black
3.0 m (118-1/8")
Class 1 (IEC/EN 60825-1:2014)
Risk Group 3 (IEC 62471-5:2015)
IEEE802.11b/g/n
DSSS, OFDM
2 412 MHz to 2 462 MHz (1 to 11ch)
IEEE802.11n
IEEE802.11g
IEEE802.11b
WPA2-PSK (AES)
DC 3 V (AA/R6/LR6 battery x 2)
Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
150 ] (5.3 ozs.) (including batteries)
Width: 47.5 mm (1-7/8"), Height: 181.5 mm (7-5/32"), Depth: 27.5 mm (1-3/32")
when [OPERATING MODE] is set to [NORMAL]
when [OPERATING MODE] is set to [ECO]
when [OPERATING MODE] is set to [QUIET]
*2*3*4
Maximum 144 Mbps
Maximum 54 Mbps
Maximum 11 Mbps
ENGLISH - 311
Advertisement
Table of Contents
